Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 768

Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 16

WARNING

Motor fire in the event of insulation overload
There is higher stress on the motor insulation through a ground fault in an IT system. If the

insulation fails, it is possible that death or severe injury can occur as a result of smoke and

fire.
● Use a monitoring device that signals an insulation fault.
● Correct the fault as quickly as possible so the motor insulation is not overloaded.

WARNING

Fire due to inadequate ventilation clearances
Inadequate ventilation clearances can cause overheating of components with subsequent

fire and smoke. This can cause severe injury or even death. This can also result in increased

downtime and reduced service lives for devices/systems.
● Ensure compliance with the specified minimum clearance as ventilation clearance for the

respective component.

WARNING

Unrecognized dangers due to missing or illegible warning labels
Dangers might not be recognized if warning labels are missing or illegible. Unrecognized

dangers may cause accidents resulting in serious injury or death.
● Check that the warning labels are complete based on the documentation.
● Attach any missing warning labels to the components, where necessary in the national

language.

● Replace illegible warning labels.

NOTICE
Device damage caused by incorrect voltage/insulation tests
Incorrect voltage/insulation tests can damage the device.
● Before carrying out a voltage/insulation check of the system/machine, disconnect the

devices as all converters and motors have been subject to a high voltage test by the

manufacturer, and therefore it is not necessary to perform an additional test within the

system/machine.

Fundamental safety instructions
1.1 General safety instructions

SINAMICS S210 servo drive system

14

Operating Instructions, 12/2017, A5E41702836B AA

«
...
14
15
16
17
18
...
»

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды