manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Руководство по эксплуатации

Поделиться
Скачать
Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 61

STO facilitates personnel to work safely with the protective door open. A classic Emergency 

Stop with electromechanical isolation is not required. The converter remains connected to the 

line and can be fully diagnosed.

Note
The distinction between Emergency Off and Emergency Stop
"Emergency Off" and "Emergency Stop" are commands that minimize different risks in the 

machine or plant.
The STO function is suitable for implementing an Emergency Stop - but not an Emergency Off.
Details regarding the distinction between Emergency Off and Emergency Stop are provided 

in the following section:

What is the difference between the Emergency Off and Emergency Stop functions? 

(Page 745)

Sequence diagram

7KHPRWRUFRDVWV

GRZQWRDVWDQGVWLOO

6SHHG

W

W

W

672DFWLYH

672GHVHOHFWLRQ

212))

5HDG\WRVWDUW

$FW

LR

Q

0R

WR

U

UH

VS

RQ

VH

&

RQ

YH

UWH

U

UH

VS

RQ

VH

During operation, STO is selected via PROFIsafe or F-DI.
The converter signals the status to the PLC via PROFIsafe for further processing.

After the response time, the drive immediately initiates safe pulse suppression. This interrupts the 
torque-generating energy fed to the motor. The motor coasts down to a standstill. STO safely 
prevents an unwanted restart of the motor.

Restart:

The converter goes into the "Ready to start" state, when STO is deselected via PROFIsafe or F-
DI.

The converter switches the motor on again with a positive signal edge at ON/OFF.

Selecting/deselecting "Safe Torque Off" 

If "Safe Torque Off" is selected, the motor holding brake is closed (if connected and configured).

Safety functions integrated in the drive

4.2 Basic Functions

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

59

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды