Qube Solutions GmbH PiXtend V2 -L- Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 146

background image

PiXtend V2 -L- Hardware Manual

understood the safety data sheet and the manuals. Training facilities must be supervised
by qualified and authorized personnel. Power supplies and accessories used must be
approved for the country in which the PiXtend V2 -L- system is to be installed and used.

2.3. Technical condition

PiXtend V2 -L-

is supplied with a pre-defined configuration, independent of its model:

•

“SPI_EN” switch activated → Communication between PiXtend & Raspberry Pi is
activated

•

“PI_5V” switch activated → PiXtend & Raspberry Pi are supplied by the same
voltage regulator on PiXtend (input voltage 12 - 24 V DC). No separate power
supply needs to be connected to the Raspberry Pi

•

All digital inputs are configured for a 24 V range (no jumper is set)

•

All analog inputs are configured for a 0..10 V range (no jumper is set)

•

"CAN" / "AO" Jumper is set to "AO" → analog outputs active, CAN inactive

•

RS485 "A" / "M" Jumper is set to "A" → automatic send/receive switching

•

Termination resistors for RS485 and CAN are not set (no jumper)

•

The microcontroller firmware is always the latest version released by Qube
Solutions. The current version can be found on our homepage

The ePLC models include additional configurations:
ePLC Basic & Pro

•

Contents of SD-Card

◦

the content is stated in the order, e.g. "CODESYS Control Demo" or "PiXtend
Basic" (in the QS-Shop)

◦

Our dealers always receive and ship the SD card "CODESYS Control Demo"

ePLC Pro

•

Housing → Stainless steel hood and DIN rail housing pre-assembled

If you need a different version or a different hardware and software combination, please
contact us directly (

info@pixtend.

com

).

www.pixtend.com

Copyright by Qube Solutions GmbH

10 / 146

«
...
8
9
10
11
12
...
»

Содержание PiXtend V2 -L-



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для PiXtend V2 -L-

Бренд: Falcon Страницы: 24

Бренд: Baldor Страницы: 34

Бренд: HARTING Страницы: 13

Бренд: XMOS Страницы: 6

XM24 Expansion Module

Бренд: Avaya Страницы: 5

TD-3316B4-16P-A1

Бренд: TVT Digital Страницы: 2

BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX

Бренд: Intel Страницы: 86

Бренд: Disc Makers Страницы: 38

Бренд: ACTi Страницы: 14

Бренд: Xilinx Страницы: 29

Бренд: McIntosh Страницы: 44

SNMP-1000-E2B1E

Бренд: Advantech Страницы: 4

Бренд: Omron Страницы: 4

ReadyNAS Duo v2

Бренд: NETGEAR Страницы: 100

Бренд: Roland Страницы: 224

Бренд: Proxim Страницы: 45

Бренд: FabiaTech Страницы: 86

Бренд: Exsys Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды