Qube Solutions GmbH PiXtend V2 -L- Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 146

background image

PiXtend V2 -L- Hardware Manual

4.2.4.Safety instructions for working with dangerous voltages

When connected to the relay on PiXtend V2 -L- with mains voltage
(115/230 V AC) or other hazardous voltage greater than 50 V, the
stainless steel hood must be connected with a protective earth (PE -
protective earth).

Cables and devices with dangerous voltages must only be
connected by trained and legally qualified personnel.

The stainless steel hood has a special connection for the protective conductor (PE). This is
marked with the designation "PE" and designed for common cable lugs or so-called "flat
plug-in sleeves" (width 6.35 mm).

www.pixtend.com

Copyright by Qube Solutions GmbH

40 / 146

Figure 27: Protective conductor connection (PE) at the

PiXtend V2 -L- hood

«
...
38
39
40
41
42
...
»

Содержание PiXtend V2 -L-



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для PiXtend V2 -L-

Бренд: Raritan Страницы: 4

Armor 101 Series

Бренд: Lochinvar Страницы: 28

Armor 101 Series

Бренд: Lochinvar Страницы: 44

Бренд: M86 Security Страницы: 309

Бренд: Eaton Страницы: 14

Бренд: Tait Страницы: 8

Бренд: C4i Страницы: 5

Бренд: Multitech Страницы: 81

Бренд: Comway Страницы: 20

NetVanta Analog Modem Dial Backup Interface Module

Бренд: ADTRAN Страницы: 2

Бренд: ZiLOG Страницы: 11

Бренд: uneron Страницы: 13

Бренд: Radica Games Страницы: 40

Бренд: Airvana Страницы: 90

Бренд: Renesas Страницы: 8

Бренд: Watchguard Страницы: 21

Бренд: ATTO Technology Страницы: 2

Бренд: Jetter Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды