Mitsubishi MOTORS Eclipse Скачать руководство пользователя страница 685

Страница: 685 / 694

ON-VEHICLE SERVICE

TSB Revision

MULTIPORT FUEL INJECTION (MFI) <3.0L>

13B-685

<Right bank and left bank heated oxygen sensor (rear)>

1. Use scan tool MB991502, observe HO2S reading. If values

are unsatisfactory, or if the scan tool is not available, use the
following procedure:

(1) Disconnect the heated oxygen sensor connector and

connect special tool MB991316 to the connector on the
heated oxygen sensor side.

(2) Make sure that there is continuity [11

−

18 ohm at 20

(68

F)] between terminal 1 (red clip of special tool) and

terminal 3 (blue clip of special tool) on the heated oxygen
sensor connector.

(3) If there is no continuity, replace the heated oxygen

sensor.

(4) Warm up the engine until engine coolant is 80

C (176

or higher.

CAUTION

Be very careful when connecting the jumper wires; incor-
rect connection can damage the heated oxygen sensor.

(5) Use the jumper wires to connect terminal 1 (red clip) of

the heated oxygen sensor connector to the positive
battery terminal and terminal 3 (blue clip) to the negative
battery terminal.

(6) Connect a digital voltage meter between terminal 2 (black

clip) and terminal 4 (white clip).

2. While repeatedly revving the engine, measure the heated

oxygen sensor output voltage.

Standard value:

3. If the sensor is defective, replace the heated oxygen sensor.

NOTE: For removal and installation of the heated oxygen sen-
sor, refer to GROUP 15, Exhaust Pipe and Main Muffler

P.15-

ENGINE

HEATED OXYGEN
SENSOR OUTPUT
VOLTAGE

REMARKS

When revving
engine

0.6

−

1.0 volt

If you make the air/
fuel ratio rich by
revving the engine
repeatedly, a
normal heated
oxygen sensor will
output a voltage of
0.6

−

1.0 volt.

AKX01624 AB

MB991316

HEATED
OXYGEN
SENSOR
EQUIPMENT
SIDE
CONNECTOR

BLUE

RED

AKX01625 AB

BLUE

JUMPER
WIRES

BLACK

RED

WHITE

MB991316

Содержание Eclipse























































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Eclipse

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi MOTORS Eclipse, Руководство пользователя

Результаты поиска

Содержание Eclipse

Отзывы:

Бренды по названию

Популярные бренды