manualshive.com logo in svg

Mitsubishi MOTORS Eclipse, Руководство пользователя

Поделиться
Скачать
Mitsubishi MOTORS Eclipse Скачать руководство пользователя страница 63

MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS

TSB Revision

MULTIPORT FUEL INJECTION (MFI) <3.0L>

13B-63

CIRCUIT OPERATION

•

Approximately 5 volts are applied to the intake air 
temperature sensor output terminal (terminal 6) 
from the ECM (terminal 62) <M/T> or PCM (ter-
minal 64) <A/T> via the resistor in the ECM <M/
T> or PCM <A/T>. The ground terminal (terminal 
5) is grounded with ECM (terminal 34) <M/T> or 
PCM (terminal 16) <A/T>.

•

The intake air temperature sensor is a negative 
temperature coefficient type of resistor. When the 
intake air temperature rises, the resistance 
decreases.

•

The intake air temperature sensor output voltage 
increases when the resistance increases and 
decreases when the resistance decreases.

.

TECHNICAL DESCRIPTION

•

The intake air temperature sensor converts the 
intake air temperature to a voltage.

•

The ECM <M/T> or PCM <A/T> checks whether 
this voltage is within a specified range.

.

DTC SET CONDITIONS

Check Conditions

•

Engine coolant temperature is higher than 76

°

C 

(169

°

F).

•

Repeat 5 or more times: drive

*1

, stop

*2

.

Drive

*1

: vehicle speed higher than 50 km/h (31 

mph) lasting a total of more than 60 seconds.

Stop

*2

: vehicle speed lower than 1.5 km/h (0.9 

mph) lasting more than 30 seconds.

Judgement Criteria

•

Changes in the intake air temperature is lower 
than 1

°

C (1.8

°

F).

.

TROUBLESHOOTING HINTS (The most likely 
causes for this code to be set are:)

•

Intake air temperature sensor failed.

•

Open or shorted intake air temperature sensor 
circuit, or loose connector.

•

ECM failed. <M/T>

•

PCM failed. <A/T>

DIAGNOSIS

Required Special Tools

•

MB991502: Scan Tool (MUT-II)

STEP 1. Using scan tool MB991502, check data list item 13: 
Intake Air Temperature Sensor.

CAUTION

To prevent damage to scan tool MB991502, always turn the 
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991502.

(1) Connect scan tool MB991502 to the data link connector.
(2) Remove the air intake hose from the volume air flow sensor.
(3) Turn the ignition switch to the "ON" position.
(4) Set scan tool MB991502 to the data reading mode for item 

13, Intake Air Temperature Sensor.

(5) Heating the sensor using a hair drier.

•

The indicated temperature increases.

NOTE: Do not allow it to increase over 80

°

C (176

°

F).

(6) Turn the ignition switch to the "LOCK" (OFF) position.
(7) Attach the air intake hose.

Q: Is the sensor operating properly?

YES : 

It can be assumed that this malfunction is intermittent. 

Refer to GROUP 00, How to Use Troubleshooting/
Inspection Service Points 

P.00-6

.

NO : 

Go to Step 2.

ACX02480

CONNECTOR : B-14

AG

INTAKE AIR
TEMPERATURE
SENSOR

AKX01621 AB

INTAKE AIR
TEMPERATURE
SENSOR

Содержание Eclipse























































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды