Mitsubishi MOTORS Eclipse Скачать руководство пользователя страница 241

Страница: 241 / 694

MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS

TSB Revision

MULTIPORT FUEL INJECTION (MFI) <3.0L>

13B-241

STEP 2. Check the left bank heated oxygen sensor (rear).

(1) Disconnect left bank heated oxygen sensor (rear) connector

B-23 and connect test harness special tool, MB991316, to
the connector on the left bank heated oxygen (rear) sensor
side.

(2) Measure the resistance between heated oxygen sensor

connector terminal 1 (red clip) and terminal 3 (blue clip).

Standard value: 11

−

18 ohm [at 20

C (68

F)]

Q: Is the resistance normal?

YES :

Go to Step 3.

NO :

Replace the left bank heated oxygen sensor (rear).
Then go to Step 12.

STEP 3. Check the power supply voltage at left bank
heated oxygen sensor (rear) harness side connector B-23.

(1) Disconnect the connector B-23 and measure at the harness

side.

(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 1 and ground.

•

Voltage should be battery positive voltage.

(4) Turn the ignition switch to the "LOCK" (OFF) position.

Q: Is the voltage normal?

YES :

Go to Step 5.

NO :

Go to Step 4.

ACX02488

LEFT BANK
HEATED OXYGEN
SENSOR (REAR)

AK103510AB

CONNECTOR: B-23

AKX01624 AB

MB991316

HEATED
OXYGEN
SENSOR
EQUIPMENT
SIDE
CONNECTOR

BLUE

RED

AKX01496

B-23 HARNESS
SIDE CONNECTOR

Содержание Eclipse























































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Eclipse

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi MOTORS Eclipse, Руководство пользователя

Результаты поиска

Содержание Eclipse

Отзывы:

Бренды по названию

Популярные бренды