manualshive.com logo in svg

Mitsubishi MOTORS Eclipse, Руководство пользователя

Поделиться
Скачать
Mitsubishi MOTORS Eclipse Скачать руководство пользователя страница 368

MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS

TSB Revision

MULTIPORT FUEL INJECTION (MFI) <3.0L>

13B-368

.

CIRCUIT OPERATION

•

Power to the evaporative emission purge sole-
noid power is supplied from the MFI relay (termi-
nal 4).

•

The ECM <M/T> or PCM <A/T> controls ground 
evaporative emission purge solenoid by turning 
the power transistor in the ECM <M/T> or PCM 
<A/T> "ON" and "OFF".

.

TECHNICAL DESCRIPTION

•

To judge if there is open circuit in the evaporative 
emission purge solenoid drive circuit, ECM <M/
T> or PCM <A/T> measures the surge voltage of 
the evaporative emission purge solenoid coil.

•

The ECM <M/T> or PCM <A/T> drives the evapo-
rative emission purge solenoid. After the solenoid 
is turned off, the ECM <M/T> or PCM <A/T> will 
check if the solenoid coil produces a surge volt-
age of 2 V or more.

.

DTC SET CONDITIONS

Check Conditions

•

Engine is being cranked.

•

Battery positive voltage is at between 10 and 16 
volts.

Judgment Criteria

•

The evaporative emission purge solenoid coil 
surge voltage (battery positive v 2 volts) 
is not detected for 0.2 second.

•

The ECM <M/T> or PCM <A/T> monitors for this 
condition once during the drive cycle.

Check Conditions

•

Battery positive voltage is at between 10 and 16 
volts.

•

ON duty cycle of the evaporative emission purge 
solenoid is between 10 and 90 percent.

•

ON duty cycle of the EGR solenoid is 0 percent.

•

Evaporative emission ventilation solenoid is OFF.

•

More than 1 second has elapsed after the above 
mentioned conditions have been met. 

Judgment Criteria

•

The evaporative emission purge solenoid coil 
surge voltage (battery positive v 2 volts) 
is not detected for 1 second. When the evapora-
tive emission purge solenoid is turned OFF.

.

TROUBLESHOOTING HINTS (The most likely 
causes for this code to be set are:)

•

Evaporative emission purge solenoid failed.

•

Open or shorted evaporative emission purge 
solenoid circuit, or loose connector.

•

ECM failed. <M/T>

•

PCM failed. <A/T>

DIAGNOSIS

Required Special Tool:

•

MB991502: Scan Tool (MUT-II)

AK000225

CONNECTOR : C-51<M/T>, C-52<A/T>

C-52

C-51

PCM<A/T>

ECM<M/T>

AJ

AK101363AB

MFI RELAY

CONNECTOR: A-18X

Содержание Eclipse























































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды