Mitsubishi MOTORS Eclipse Скачать руководство пользователя страница 231

Страница: 231 / 694

MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS

TSB Revision

MULTIPORT FUEL INJECTION (MFI) <3.0L>

13B-231

STEP 2. Check the left bank heated oxygen sensor (rear).

(1) Disconnect the left bank heated oxygen sensor (rear)

connector B-23 and connect test harness special tool,
MB991316, to the connector on the left bank heated oxygen
sensor (front) side.

(2) Warm up the engine until engine coolant 80

C (176

F) or

higher.

CAUTION

Be very careful when connecting the jumper wires; incor-
rect connection can damage the right bank heated oxygen
sensor (rear).

(3) Use the jumper wires to connect terminal 1 (red clip) to the

positive battery terminal and terminal 3 (blue clip) to the
negative battery terminal.

(4) Connect a digital volt meter between terminal 2 (black clip)

and terminal 4 (white clip).

(5) While repeatedly revving the engine, measure the left bank

heated oxygen sensor (rear) output voltage.

Standard value: 0.6

−

1.0 volt

Q: Is the voltage at the standard value?

YES :

Go to Step 3.

NO :

Replace the left bank heated oxygen sensor (rear).
Then go to Step 5.

ACX02488

LEFT BANK
HEATED OXYGEN
SENSOR (REAR)

AK103510AB

CONNECTOR: B-23

AKX01625 AB

BLUE

JUMPER
WIRES

BLACK

RED

WHITE

MB991316

Содержание Eclipse























































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Eclipse

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi MOTORS Eclipse, Руководство пользователя

Результаты поиска

Содержание Eclipse

Отзывы:

Бренды по названию

Популярные бренды