IBM i 830 Скачать руководство пользователя страница 929 | Manualshive

Страница: 929 / 1000

background image

d.

Select the Work with disk unit recovery option on the Work with Disk
Unit display.

e.

Select the Recover configuration option on the Work with Disk Unit
Recovery display. This option assembles the system configuration
information on disk unit 1 in the system unit.

Notes:

a.

A warning message appears stating that recovering the configuration
destroys all system data.

b.

If you have a system with only one disk unit, a message may appear
stating that your request to recover the configuration was not successful.
The recover configuration function cannot be performed on a system with
only one disk unit.

Continue with the next step of this procedure.

18.

The ASP to which the failing disk unit was assigned is cleared. The customer
should do the following:

v

If the disk unit you exchanged is in ASP 1, have the customer see the
Backup and Recovery information. You must restore the operating system
(OS/400 Licensed Program) and all customer data.

v

If the disk unit is in a user ASP (ASP 2 through ASP 16), data in the ASP is
lost. See the Backup and Recovery information.

This ends the procedure.

19.

Perform an IPL from removable media and restore the Licensed Internal Code
(see “Restoring Licensed Internal Code” in the

iSeries Service Functions

information). This information shows you how to perform an IPL and restore
the Licensed Internal Code.

Note:

Some objects may be damaged. The customer may have to load the
damaged objects again (see the

Backup and Recovery

information).

This ends the procedure.

20.

Is the failing unit missing from the configuration?

No

Yes

↓

Go to step 31 of this procedure.

21.

Find another disk unit on the system, other than the load-source disk unit.

22.

Perform the following to install a new disk unit on the system:

a.

Power off the system.

b.

Slide the disk unit you found in step 21 of this procedure out of the
system (see “Chapter 4. Removal and Installation Procedures” on
page 617).

c.

Be very careful with the disk unit. You will install it again when the repair
actions to the failing disk unit are complete.

d.

Install the new disk unit.

23.

Perform an IPL to DST (see “Dedicated Service Tools (DST)” in the

iSeries

Service Functions

information).

Does the Use Dedicated Service Tools (DST) display appear?

Yes

No

↓

Repeat step 1 of this procedure.

Data Recovery and General System Information

Chapter 6. Data Recovery Procedures and General System Information

915

«
...
927
928
929
930
931
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

Бренд: IBM Страницы: 198

Eserver xSeries 360 Type 8686

Бренд: IBM Страницы: 74

Бренд: AXIOMTEK Страницы: 55

Бренд: IBM Страницы: 48

SUPERSERVER 1028UX-CR-LL1

Бренд: Supermicro Страницы: 128

Express5800/R320f-E4

Бренд: NEC Страницы: 88

ProLiant ML350 Gen10

Бренд: Hewlett Packard Enterprise Страницы: 214

ANTMINER S19 Pro

Бренд: BITMAIN Страницы: 17

Бренд: Adtec Страницы: 2

Бренд: Allnet Страницы: 12

SCB2 - Server Board Motherboard

Бренд: Intel Страницы: 108

Бренд: FieldServer Страницы: 12

Бренд: Gigabyte Страницы: 84

Бренд: Yawarra Страницы: 4

Бренд: QNAP Страницы: 97

Бренд: IBM Страницы: 170

MAXserver 1608A

Бренд: NBase-Xyplex Страницы: 164

BladeCenter JS12

Бренд: IBM Страницы: 318

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды