IBM i 830 Скачать руководство пользователя страница 928 | Manualshive

Страница: 928 / 1000

background image

13.

The system is ready for the next IPL.

This ends the procedure.

14.

Perform the following to remove the failing load-source disk unit on the
system:

a.

Power off the system.

b.

Find the load-source disk unit. Slide the disk unit out of the system (see
“Chapter 4. Removal and Installation Procedures” on page 617).

c.

Install the new disk unit.

15.

Perform an IPL from removable media and select the option to install
Licensed Internal Code and recover the configuration. (See “Installing
Licensed Internal Code” in the

iSeries Service Functions

information, which

performs an IPL and installs the Licensed Internal Code.)

16.

Did you get a Disk Configuration Error Report with a “

Unit has incorrect

logical partition configuration

” warning?

No

Yes

↓

You have logical partitions that need to be recovered before you can
continue with this disk unit recovery procedure.

Perform the following:

a.

Enter the

Use Dedicated Service Tools (DST)

option from the IPL or

Install the System display.

b.

Enter the password 22222222.

Note:

If this password is not valid, ask the customer for the
correct password.

c.

Select the

Work with system partitions

option on the Use Dedicated

Service Tools (DST) display.

d.

Select the

Recover configuration data

option on the Work with

System Partitions display.

e.

Select the

Recover primary partition configuration data

option on the

Recover Configuration Data display.

f.

Review the information on the Select Disk Unit for Configuration
Data Recovery display. Select the disk unit with the most recent
date and correct system serial number and press enter.

g.

The system automatically copies the configuration data to the
primary partition’s load source, and performs an IPL.
Continue with the next step of this procedure.

17.

The system ASP will be cleared because customer data was not recoverable.
Recover the configuration to disk unit 1 in the system unit by doing the
following:

a.

Enter the Use Dedicated Service Tools (DST) option from the IPL or Install
the System display.

b.

Enter the password 22222222.

Note:

If this password is not valid, ask the customer for the correct
password.

c.

Select the Work with disk units option on the Use Dedicated Service Tools
(DST) display.

Data Recovery and General System Information

914

iSeries Model 830, 840, SB2, and SB3 Problem Analysis, Repair and Parts V5R1

«
...
926
927
928
929
930
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

Бренд: Sun Microsystems Страницы: 148

eserver xSeries 306

Бренд: IBM Страницы: 46

Бренд: HPE Страницы: 174

Бренд: Velleman Страницы: 17

Бренд: IBM Страницы: 76

Бренд: Data-Tronix Страницы: 29

Бренд: Data-Tronix Страницы: 30

C12C823912 - Net 2 Print Server

Бренд: Epson Страницы: 20

C823622A - Interface Type B Print Server

Бренд: Epson Страницы: 3

C12C800WN (Net 802.11b Wireless Print Server)

Бренд: Epson Страницы: 2

C32C824461 - UB R03 Print Server

Бренд: Epson Страницы: 86

Бренд: Epson Страницы: 279

C823622A - Interface Type B Print Server

Бренд: Epson Страницы: 2

Бренд: Cisco Страницы: 2

Бренд: NEC Страницы: 12

Бренд: NEC Страницы: 20

Бренд: NEC Страницы: 16

Бренд: NEC Страницы: 504

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды