IBM i 830 Скачать руководство пользователя страница 635 | Manualshive

Страница: 635 / 1000

background image

CAUTION:
The circuit card contains lead solder. To avoid the release of lead (Pb) into the
environment, do not burn. Discard the circuit card as instructed by local
regulations. (RSFTC234)

1.

Select

System Service Tools (SST)

. If you cannot get to SST, select DST.

Attention:

Do not perform a system IPL to get to DST.

2.

Select

Start a Service Tool

.

3.

Select

Hardware Service Manager

.

4.

Select

Packaging hardware resources

.

5.

Select

Hardware contained within package

for the Frame ID that contains the IOA

or IOP that you are removing.

6.

Find the card position for the IOA or IOP that you are removing and select
the

Concurrent maintenance

option.

7.

A listing of the power domain is shown. Select the

Power off domain

function

key. Everything within the IOA’s or IOP’s power domain will be powered off .

8.

To see the status of the power domain, select the

Display power states

function

key.

9.

Find the IOA or IOP that you are removing and select the

Toggle LED blink

off/on

option.

10.

Remove the cover to access the card that you are removing from the system.
See “FC 5074, FC 5079, FC 9079 – Covers” on page 623.

11.

Remove the EMC access plate that is located directly above the card enclosure.
Press the two latching mechanisms together and tilt the top of the cover away
from the frame to remove it.

12.

Look at the power LED (

W

) for the card that you are removing to ensure that it

is powered off. The power LED (

W

) is located to the left and directly above the

card slot. If the LED is blinking multiple times per second (rapidly) or it is off,
then the card is powered off.

13.

Disconnect and label any cables from the card that you wish to remove.

14.

Turn the blue latch counter clockwise and lift upward on the black latch to
release the card.

15.

Gently pull the card off the backplane.

This ends the procedure.

Concurrent Installation Procedure:

All cards are sensitive to electrostatic discharge (see “Appendix C. Working with
Electrostatic Discharge-Sensitive Parts” on page 955).

CAUTION:
The circuit card contains lead solder. To avoid the release of lead (Pb) into the
environment, do not burn. Discard the circuit card as instructed by local
regulations. (RSFTC234)

1.

Install the card in to the system by reversing the card removal procedure
above.

2.

Select the

Power on domain

function key for the IOA or IOP that you are

installing.

Note:

To the right of the description field you will see one or both of the
following symbols displayed:

Remove and Replace Procedures

Chapter 4. Removal and Installation Procedures

621

«
...
633
634
635
636
637
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

Бренд: Samsung Страницы: 7

5big - Network NAS Server

Бренд: LaCie Страницы: 9

Бренд: LaCie Страницы: 14

ProLiant DL180 Gen10

Бренд: HPE Страницы: 10

Бренд: IBM Страницы: 74

Бренд: Buffalo Страницы: 2

SUPERO SuperServer 6026TT-H6IBQRF

Бренд: Supero Страницы: 110

ProLiant ML350 G3

Бренд: HP Страницы: 44

ProLiant ML310e Gen8 v2

Бренд: HP Страницы: 43

ProLiant ML330 Generation 3

Бренд: HP Страницы: 34

PROLIANT ML350 G6

Бренд: HP Страницы: 145

ProLiant ML350 Gen9

Бренд: HP Страницы: 171

PROLIANT ML350 G6

Бренд: HP Страницы: 103

PROLIANT ML330 G6

Бренд: HP Страницы: 137

Бренд: LG Страницы: 100

Бренд: LG Страницы: 35

SUPERSERVER 6113L-8

Бренд: Supero Страницы: 104

SUPERSERVER 6017R-NTF

Бренд: Supero Страницы: 126

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды