IBM i 830 Скачать руководство пользователя страница 288 | Manualshive

Страница: 288 / 1000

background image

Reference
Code

Description/Action Perform all actions before exchanging
Failing Items

Failing Item

Location

7777

Hardware configuration change detected

A hardware resource is missing. The resource reported in to the
system on a previous IPL, but has not reported in on the
current IPL. This could occur for several different reasons.

1.

It could be a normal situation where the resource is
currently powered off. In this case, when the resource is
powered back on, it will no longer be missing.

2.

The hardware resource could also be missing if it has been
removed from the system, for example, a tape drive that
was replaced with a different tape drive. The service
representative should use the Hardware service manager to
remove the entry for this resource.

3.

The resource may not have reported in on this IPL because
it is failing. Perform problem analysis to determine why the
resource is failing.

CFFC

Optical library device condition not expected

The optical disk drive addressing within the optical library is
incorrect. This error is likely to be the result of faulty cabling or
switch setting following service to an optical library.

Contact your hardware service provider.

OPTLCBL
DRVSWCH

CFFD

Optical drive failure

OPTLDRV

CFFF

Media determined to be bad in Optical library

F103

Main storage dump must be copied for service.

Perform “LIC-PIP1” on page 342.

FDC0

LIC program reported informational error

This reference code is logged for information only. No action
required.

FDC5

LIC program failed and data was captured

This reference code indicates first failure data capture (FFDC)
data was collected for a problem reported by licensed internal
code.

The user should dial IBM Software Support for assistance.

GG3FFDC

Licensed Internal Code (LIC) Failing Items

Failing Item

Description

Document Description

21H7625

Incorrect, defective or missing SCSI jumper card Repair and Parts; removal and installation

procedures

AJDG301

Licensed Internal Code

Service Functions; APAR or LICTR

AJDGP01

Service processor Licensed Internal Code

Repair and Parts; removal and installation
procedures

AJGLD01

I/O card Licensed Internal Code

Service Functions; APAR or LICTR

BACKPLN

Card enclosure or backplane

Problem Analysis; Symbolic FRU Isolation

BSTWRPL

I/O tower card

Problem Analysis; Symbolic FRU Isolation

B6xx (including A6xx)

274

iSeries Model 830, 840, SB2, and SB3 Problem Analysis, Repair and Parts V5R1

«
...
286
287
288
289
290
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

Бренд: A10 Networks Страницы: 17

Бренд: 7starlake Страницы: 32

x3100 M5 Type 5457

Бренд: IBM Страницы: 688

SUPERSERVER 5018D-FN8T

Бренд: Supermicro Страницы: 124

AlphaServer ES45 1B

Бренд: Compaq Страницы: 322

PCS400R Pro:Centric

Бренд: LG Страницы: 57

Бренд: LG Страницы: 104

Pro:Centric PCS200S

Бренд: LG Страницы: 40

Бренд: LG Страницы: 6

PCS500R Pro:Centric

Бренд: LG Страницы: 70

Бренд: LG Страницы: 24

Centric PCS150R Pro

Бренд: LG Страницы: 35

Centric PCS200R Pro

Бренд: LG Страницы: 384

TS-401T Turbo Server

Бренд: QNAP Страницы: 8

Бренд: National Instruments Страницы: 4

InterServe 80 SL

Бренд: Intergraph Страницы: 106

Бренд: Axis Страницы: 10

NETWORK SATELLITE 5.2 - CHANNEL MANAGEMENT

Бренд: Red Hat Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды