IBM i 830 Скачать руководство пользователя страница 172

Страница: 172 / 1000

Reference Code

Description/Action Perform all actions before exchanging Failing Items

Failing Item

9102

Gateway device detected a SCSI interface error

Use the gateway device service documentation to analyze the problem.

FI00871
FCGATE
FI00872
DEVTERM

9200

I/O processor addressed the tape unit; no response

If the attached device is an external device, do the following before
exchanging any parts:

Ensure that the device is powered on.

If an interposer is required, make sure that it is connected between the
I/O processor and the SCSI cable.

Ensure that the SCSI cable is seated correctly, and that there are no bent
or damaged pins on the SCSI cable.

Ensure that a terminating plug is attached to the device end of the SCSI
cable.

FI00871
FI01112
FI00872
DEVTERM

9201

Tape unit command timeout

If the attached device is an external device, do the following before
exchanging any parts:

Ensure that the device is powered on.

If an interposer is required, make sure that it is connected between the
I/O processor and the SCSI cable.

Ensure that the SCSI cable is seated correctly, and that there are no bent
or damaged pins on the SCSI cable.

Ensure that a terminating plug is attached to the device end of the SCSI
cable.

FI00871
FI01112
FI00872
DEVTERM
MH7TMED

9202

Tape unit failed after Licensed Internal Code was loaded

If the attached device is an external device, do the following before
exchanging any parts:

Ensure that the device is powered on.

If an interposer is required, make sure that it is connected between the
I/O processor and the SCSI cable.

Ensure that the SCSI cable is seated correctly, and that there are no bent
or damaged pins on the SCSI cable.

Ensure that a terminating plug is attached to the device end of the SCSI
cable.

FI00871
FI01112
FI00872
DEVTERM

9210

Illegal or unsupported tape unit response

FI00871
FI01112
FI00130

9211

Gateway device detected a bus protocol error

Use the gateway device service documentation to analyze the problem.

FCGATE
FCIOA
FI00871
ANYFC
FCCABLE
FI00872
DEVTERM

9300

Tape unit failure

FI00871

9301

Tape device failure, redundancy lost

The tape unit detected a hardware failure that does not prevent the tape
unit from completing the current operation.

FI00871

63A0

158

iSeries Model 830, 840, SB2, and SB3 Problem Analysis, Repair and Parts V5R1

Содержание i 830








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание i 830

Отзывы:

Похожие инструкции для i 830

Бренды по названию

Популярные бренды

IBM i 830, Руководство по ремонту

Результаты поиска

Содержание i 830

Отзывы:

Похожие инструкции для i 830

Бренды по названию

Популярные бренды