IBM i 830 Скачать руководство пользователя | Manualshive

Страница: 619 / 1000

background image

UJE34

The error message may have been logged from a temporary error that is not
caused by equipment failure. This type of error message sometimes contains
information about system performance.

See the original system message for cause and recovery information about the
error.

UJE35

The configuration parameter that was identified as a possible problem can be
verified by displaying the local area network line description with the DSPLIND
command.

The line description was created by the CRTLINTRN, the CRTLINETH or the
CRTLINDDI command. You may need to review the appropriate command
information to determine if the configuration parameter is wrong.

For more information about commands related to communications, see the
Programming: Control Language and the Communications Configurations
reference topics in the iSeries 400 Information Center, which is available at
http://www.ibm.com/eserver/iseries/infocenter

Some software problems can be temporarily solved by changing the configuration
parameter, even if the original value was correct. Report this problem to your
service representative if you use this temporary change.

This ends the procedure.

UJE40

The problem may be at the remote site or on the network media.

Perform the following:

1.

Ask the remote site operator to verify the following:

v

The remote equipment is powered on and ready.

v

The configuration values are correct.

v

The local area network cables are securely connected and are not damaged.

2.

If the problem continues, run all available diagnostic tests on the remote
equipment and perform the repair action specified.

This ends the procedure.

ULNZ3

Communications line problems:

When a workstation is attached to the system through modems, it may fail or lose
communication with the system for various lengths of time. This is due to a
communications line problem.

Refer to the modem service information to determine how to test the modems and
verify that the communications line between the modems is working correctly.

This ends the procedure.

Symbolic FRUs

Chapter 3. Problem Isolation Procedures (PIPs), Failing Items, and Symbolic FRU Isolation

605

«
...
617
618
619
620
621
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

Бренд: Xerox Страницы: 8

FusionServer CH242 V5

Бренд: xFusion Digital Technologies Страницы: 61

Бренд: KYLAND Страницы: 30

Бренд: QNAP Страницы: 68

EonStor GS 3000 Series

Бренд: Infortrend Страницы: 134

Бренд: Artesyn Embedded Technology Страницы: 2

TS-401T Turbo Server

Бренд: QNAP Страницы: 8

Бренд: GRASS VALLEY Страницы: 2

Бренд: Digital Watchdog Страницы: 7

Blackjack Tower DW-BJST51T Series

Бренд: Digital Watchdog Страницы: 14

Бренд: XtendLan Страницы: 38

Бренд: Echostreams Страницы: 3

cPCI-6510 Series

Бренд: ADLINK Technology Страницы: 112

Бренд: Pepperl+Fuchs Страницы: 28

AS2021M-UR Plus

Бренд: Supero Страницы: 104

Бренд: Supero Страницы: 104

AS-1041M-T2 Plus

Бренд: Supero Страницы: 98

Бренд: Supero Страницы: 135

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды