IBM i 830 Скачать руководство пользователя страница 672 | Manualshive

Страница: 672 / 1000

background image

at the following URL:
http://www.storage.ibm.com/hardsoft/products/ess/refinfo

This ends the procedure.

Models 830/SB2 with FC 9074 – Cards – Dedicated

Attention:

All cards are sensitive to electrostatic discharge (see “Appendix C.

Working with Electrostatic Discharge-Sensitive Parts” on page 955).

CAUTION:
The circuit card contains lead solder. To avoid the release of lead (Pb) into the
environment, do not burn. Discard the circuit card as instructed by local
regulations. (RSFTC234)

In some cases you do not need to power down the system in order to change PCI
cards. Use the rules in “Models 830/SB2 with FC 9074 – Cards – Concurrent” on
page 655 to determine if you should use dedicated or concurrent removal and
installation procedures.

Perform the following:

1.

Power off the system (see “Powering On and Powering Off the System and
Logical Partitions” on page 922).

2.

Disconnect the AC power cord from the tower that you are working on.

3.

Are you removing a

processor capacity card

or an

interactive Card

(N02–A,

N02–B) card?

No

Yes

↓

Go to “Models 830/SB2 with FC 9074 – System Unit Control Panel
(NB1)” on page 667.

This ends the procedure.

4.

Are you removing cards in a Model 830/SB2

(FC 9074)

Base I/O Tower?

No

Yes

↓

Go to step 30 on page 662 of this procedure.

5.

You are removing a card in the Model 830/SB2 system unit (processor
drawer) using Dedicated Maintenance

Open the rear cover (see “Models

830/SB2 with FC 9074 – Covers” on page 663).

Refer to “Assembly 3: Models 830 and SB2 with FC 9074 – Final Assembly, Rear”

on page 814 and perform the following steps.

6.

Remove the mounting screws from the EMC shield that is located directly
above the (lower) card enclosure in the (FC 9074) Base I/O Tower portion of
the Model 830/SB2 system. See “Models 830 and SB2 with FC 9074 - Final
Assembly, Rear” on page 820.

7.

Remove the EMC shield from the frame.

8.

Disconnect and label the cables that go from the (lower) card enclosure in the
(FC 9074) Base I/O Tower to the (upper) processor drawer in the system unit.

Note:

When reassembling the system, put the safety plate back covering the
cables.

9.

Reach through the opening and loosen the thumbscrew that is holding the
safety plate to the bottom of the Processor drawer of the system unit.

Remove and Replace Procedures

658

iSeries Model 830, 840, SB2, and SB3 Problem Analysis, Repair and Parts V5R1

«
...
670
671
672
673
674
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

Enterprise Server S80

Бренд: IBM Страницы: 282

eServer 380 xSeries

Бренд: IBM Страницы: 112

4-Port USB 2.0 Device Server over IP...

Бренд: Quatech Страницы: 2

Бренд: Huawei Страницы: 2

Бренд: Huawei Страницы: 52

Бренд: Huawei Страницы: 122

Бренд: Huawei Страницы: 131

UPS5000-E-****-FM series

Бренд: Huawei Страницы: 261

Бренд: Samsung Страницы: 58

Бренд: ClearCube Страницы: 15

VANTAGE RADIUS 50

Бренд: ZyXEL Communications Страницы: 1

Бренд: ZyXEL Communications Страницы: 4

Бренд: Obvius Страницы: 39

Бренд: Rittal Страницы: 64

Бренд: Check Point Страницы: 41

Dual Processor AS 1020C-3

Бренд: Supero Страницы: 106

Бренд: Celestix Страницы: 68

Бренд: Supero Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды