IBM i 830 Скачать руководство пользователя страница 190 | Manualshive

Страница: 190 / 1000

background image

Reference
Code

Description/Action Perform all actions before exchanging
Failing Items

Failing Item

9302

Tape device failure or media error

The tape unit detected a failure that may be caused by a
hardware failure or a media error.

Refer to the tape unit service information for possible
information on diagnostic tests that can be run to isolate
between hardware and media failures.

MLYTMED
86G9251

9310

Licensed Internal Code for the tape unit is not correct

86G9251
FI00130

9320

Tape device Licensed Internal Code failure

FI00130
86G9251

9350

Tape unit detected a read or write error on tape medium

A permanent read or write error occured. Clean the tape
unit and retry the operation.

If cleaning the tape unit does not correct the problem,
exchange the tape media.

MLYTMED
86G9251

9351

Tape with excessive error rate was mounted in tape
device.

The tape unit detected that the mounted tape cartridge has
a history of excessive read and write errors. It is
recommended that you exchange the tape cartridge.

MLYTMED
ULYCLN
86G9251

9355

The data format is incorrect; the tape cannot be read

The tape unit has detected that the data format on the
tape media is not supported.

Clean the tape unit and retry the operation.

If the operation continues to fail, use a different tape
cartridge.

ULYUSR1
MLYTMED
ULYCLN
86G9251

9500

I/O processor Licensed Internal Code error

If the system is operational, take a dump of the I/O
processor data. For more infomration, see the

iSeries Service

Functions

information or ask your next level of support for

assistance.

FI00130

9600

Equipment Check Failure on Library Device.

See library device service information to resolve the error.

LIBDEV

9800 to 9803

I/O processor successfully recovered from temporary error

No action required. This reference code is logged for
information only.

9810

Problem analysis has determined a part should be
replaced.

This reference code is used for ending Online Problem
Analysis with a list of failing items. (Information only)

9427

176

iSeries Model 830, 840, SB2, and SB3 Problem Analysis, Repair and Parts V5R1

«
...
188
189
190
191
192
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

Бренд: HPE Страницы: 174

UniServer E3200 G3

Бренд: H3C Страницы: 401

Бренд: Velvac Страницы: 55

ProLiant DL580 Gen10

Бренд: HPE Страницы: 158

SUPERSERVER 6015C-M3

Бренд: Supero Страницы: 118

NPort W2150Plus Series

Бренд: Moxa Technologies Страницы: 167

Бренд: Seyeon Страницы: 10

UniServer R4300 G6

Бренд: H3C Страницы: 542

SILVERSTREAM 3.75

Бренд: RSA Security Страницы: 11

Бренд: Multitech Страницы: 35

Usb Peripheral Server/5

Бренд: Black Box Страницы: 10

Бренд: Black Box Страницы: 3

Бренд: Tibbo Страницы: 21

DIRECTORY SERVER 7.1 SP7 - S

Бренд: Red Hat Страницы: 12

Бренд: Xantech Страницы: 52

Бренд: Star Lake Страницы: 50

CHALLENGE CMN A012B

Бренд: Silicon Graphics Страницы: 40

Com Port Redirector

Бренд: Lantronix Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды