IBM i 830 Скачать руководство пользователя страница 640 | Manualshive

Страница: 640 / 1000

background image

7.

Remove the cables from the rear of the DASD board assembly and note their
locations.

Note:

Both ends of the ribbon cables are marked “

LH

” or “

RH

” indicating that

one end of the cable is plugged in to either the left-hand (DB1) or
right-hand (DB2) DASD board assembly. The other end of the cable is
plugged in to either the left-most (LH) or right-most (RH) DASD
controller card (The cables will crisscross in the center of the tower).

8.

Remove the DASD board assembly.

9.

Install the DASD board assembly by reversing the removal procedure. After
exchanging an item, go to “Verifying the Repair” on page 920.

This ends the procedure.

FC 5074, FC 5079, FC 9079 – Device Board – DB3

1.

Power off the expansion tower (see “Powering On and Powering Off the
System and Logical Partitions” on page 922).

2.

Disconnect the power cord from the expansion tower.

3.

Open the rear cover. (See “FC 5074, FC 5079, FC 9079 – Covers” on page 623.)

4.

From the rear of the expansion tower

remove

the following:

a.

Remove the EMC access plate that is located directly above the tower card
enclosure. Press the surfaces of the two latching mechanisms together and
tilt the top of the cover away from the frame to remove it.

b.

Remove the cables from the disk unit controller cards (IOAs) that are
located inside the PCI card enclosure and note their locations.

Note:

Both ends of the ribbon cables are marked “

LH

” or “

RH

” indicating

that one end of the cable is plugged in to either the left-hand (DB1)
or right-hand (DB2) DASD board assembly. The other end of the
cable is plugged in to either the left-most (LH) or right-most (RH)
DASD controller card (The cables will crisscross in the center of the
tower).

c.

Remove the screws that hold the tower card enclosure in the frame.

d.

Pull the tower card enclosure partially out of the frame while lifting the
cables clear of the enclosure.

e.

Press the release mechanism that is located along the top right side of the
enclosure and carefully slide the enclosure towards you. Make sure that the
cables are clear of the enclosure.

f.

Remove the tower card enclosure from the frame.

g.

Remove the screws from the EMC access plate that is located inside the
frame and directly above the power distribution board.

h.

Remove the EMC access plate.

i.

Reach through the opening and remove the cables from the backside of the
base DASD board assembly (DB3).

5.

Open the front cover. (See “FC 5074, FC 5079, FC 9079 – Covers” on page 623.)

6.

From the front of the expansion tower

remove

the following:

a.

Note the removable media locations and then remove them by pulling out
on the handles which are located on each side of the unit.

Remove and Replace Procedures

626

iSeries Model 830, 840, SB2, and SB3 Problem Analysis, Repair and Parts V5R1

«
...
638
639
640
641
642
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

Бренд: Cabletron Systems Страницы: 93

Бренд: IBM Страницы: 51

Бренд: TAPKO Страницы: 2

BladeCenter PS703

Бренд: IBM Страницы: 198

LaCinema PlayHD

Бренд: LaCie Страницы: 2

Бренд: QNAP Страницы: 16

Бренд: Koon Technology Страницы: 20

Бренд: Super Страницы: 60

WF01 64 V2 Series

Бренд: Lanberg Страницы: 22

Бренд: Dell EMC Страницы: 25

Бренд: Dell EMC Страницы: 184

Бренд: Planet Страницы: 108

SecureBox SDS1100

Бренд: Lantronix Страницы: 75

Бренд: Lantronix Страницы: 141

Бренд: Gigabyte Страницы: 67

Бренд: Gigabyte Страницы: 166

Бренд: Synology Страницы: 182

Бренд: JAHT Страницы: 85

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды