IBM i 830 Скачать руководство пользователя страница 632 | Manualshive

Страница: 632 / 1000

background image

Models 840/SB3 – Time of Day (TOD) Battery .

. 697

Disk Unit – Dedicated and Concurrent .

.

.

.

. 698

Disk Unit, Models 830/SB2 and 840/SB3 –
Dedicated and Concurrent .

.

.

.

.

.

.

. 698

Concurrent Maintenance – Removal and
Installation .

.

.

.

.

.

.

.

.

.

.

. 698

Dedicated Maintenance – Removal and
Installation .

.

.

.

.

.

.

.

.

.

.

. 700

Tape Cartridge – Manual Removal .

.

.

.

.

. 701

6383, 6385, 6386, 6387 Tape Cartridge .

.

.

. 701

Locked Position

.

.

.

.

.

.

.

.

.

. 701

Standby Position .

.

.

.

.

.

.

.

.

. 701

1/4 inch Tape Cartridge (Type 6335).

.

.

.

. 702

Optical Media – Manual Removal

.

.

.

.

.

. 704

CD-ROM and DVD .

.

.

.

.

.

.

.

.

. 704

Emergency Disc Ejection Function

.

.

.

. 704

Attention:

If removing the cover while powered on, errors may occur due to

Electromagnetic Interference.

This is the starting point for all remove procedures in the 1.6 meter rack. Perform
the following steps.

Attention:

It is not always necessary to power off the system to exchange a field

replaceable unit (FRU). You will be directed through a concurrent exchange, if
possible, for disk or removable media storage units.

1.

Find the location of the part you are replacing in “Locations and Addresses” on
page 705.

2.

If you are removing a IOA, IOP, IXS card, disk unit or removable media unit,
you may be able to use the concurrent procedures and keep the system up and
running.

3.

Find the FRU you are removing in this section and follow the procedures.

4.

When you have completed the remove procedure, install the FRU by reversing
the remove procedure unless otherwise noted.

5.

After exchanging an item, see “Verifying the Repair” on page 920.

FC 5074, FC 5079, FC 9079 (With Single Line Cord) – AC Charger – A01

1.

Power off the expansion tower. (See “Powering On and Powering Off the
System and Logical Partitions” on page 922.)

2.

Disconnect the incoming AC power cord from the expansion tower.

3.

Open the rear cover. (See “FC 5074, FC 5079, FC 9079 – Covers” on page 623.)

4.

Disconnect all the power cords from the battery charger.

5.

Remove the screws that are holding the charger to the frame.

6.

Remove the battery charging unit.

7.

Install the battery charger by reversing the removal procedure. After
exchanging an item, go to “Verifying the Repair” on page 920.

This ends the procedure.

FC 5074, FC 5079, FC 9079 (With Dual Line Cord) – AC Charger – A01

1.

Do Not Power Down the tower if it is powered on. (This can be done
concurrently.)

2.

Open the rear cover. See “FC 5074, FC 5079, FC 9079 – Covers” on page 623.

3.

See the Table 44 on page 737.

4.

Trace the AC input line cord that connects to AC module that needs replacing
and disconnect that AC line cord.

Attention:

Do

not

disconnect the other system AC line cord when powered

on.

Remove and Replace Procedures

618

iSeries Model 830, 840, SB2, and SB3 Problem Analysis, Repair and Parts V5R1

«
...
630
631
632
633
634
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

Бренд: A10 Networks Страницы: 17

Netfinity 6000R

Бренд: IBM Страницы: 218

eserver xSeries 440

Бренд: IBM Страницы: 74

eserver xSeries 440

Бренд: IBM Страницы: 98

eserver xSeries 440

Бренд: IBM Страницы: 84

Eserver xSeries 360 Type 8686

Бренд: IBM Страницы: 184

eserver xSeries 350

Бренд: IBM Страницы: 62

eServer xSeries 135

Бренд: IBM Страницы: 62

eserver pSeries 690

Бренд: IBM Страницы: 212

System x3690 X5

Бренд: IBM Страницы: 32

System x3690 X5

Бренд: IBM Страницы: 33

System x3690 X5

Бренд: IBM Страницы: 180

Бренд: IBM Страницы: 1032

Бренд: Lantronix Страницы: 299

Бренд: Axis Страницы: 10

Бренд: B&B Страницы: 55

Server 3100 series

Бренд: Digital Equipment Страницы: 71

Бренд: Yawarra Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды