IBM i 830 Скачать руководство пользователя страница 450 | Manualshive

Страница: 450 / 1000

background image

No

Yes

↓

This ends the procedure.

9.

Has the system been powered off for several days?

Yes

No

↓

Ask your next level of support for assistance.

This ends the procedure.

10.

The cache battery pack may be depleted. Do NOT replace the I/O adapter or
the cache battery pack.
Reclaim the cache storage (see “Reclaim IOP Cache Storage” on page 947).

Note:

The system operator may want to restore data from the most recent
saved tape after you complete the repair.

11.

Does the IPL complete successfully?

No

Yes

↓

This ends the procedure.

12.

Ask your next level of support for assistance.

This ends the procedure.

SDIOP-PIP32

Introduction:

Note:

Determine if the system has logical partitions. Go to “Determining if the
System Has Logical Partitions” on page 943, before continuing with this
procedure.

Note:

If the system has logical partitions, perform this procedure from the logical
partition that reported the problem.

You were sent to this procedure from URC 9011.

Attention:

There is data in the cache of this I/O card, that belongs to devices

other than those that are attached. Customer data may be lost.

1.

Did you just exchange the storage I/O adapter as a result of a failure?

Yes

No

↓

Go to step 5 of this procedure.

2.

You have just exchanged a storage I/O adapter.
Reclaim the cache storage (see “Reclaim IOP Cache Storage” on page 947).

3.

Does the IPL complete successfully?

No

Yes

↓

This ends the procedure.

4.

Go to “Starting Point for All Problems” on page 4 to correct the problem.

This ends the procedure.

5.

Have the I/O cards been moved or reconfigured recently?

Yes

No

↓

Ask your next level of support for assistance.

This ends the procedure.

SDIOP PIPs

436

iSeries Model 830, 840, SB2, and SB3 Problem Analysis, Repair and Parts V5R1

«
...
448
449
450
451
452
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

Бренд: TANDBERG Страницы: 276

BladeCenter HS23

Бренд: IBM Страницы: 28

NEAX2000 IVS Series

Бренд: NEC Страницы: 160

SUPERSERVER 5018A-MHN4

Бренд: Supermicro Страницы: 116

CE-HE130S4 Series

Бренд: Ablecom Страницы: 43

Бренд: t.a.c. Страницы: 36

TS-U100 - NAS Server - USB

Бренд: TRENDnet Страницы: 47

Бренд: LOYTEC Страницы: 4

Бренд: IBM Страницы: 90

301P - DP Print Server

Бренд: D-Link Страницы: 150

Бренд: TAG Страницы: 84

8-BAY RACKMOUNT NAS

Бренд: Seagate Страницы: 20

BlackArmor NAS 420

Бренд: Seagate Страницы: 64

Бренд: Kramer Страницы: 28

Бренд: ClearCube Страницы: 2

LANTIME M600/GPS

Бренд: Meinberg Страницы: 6

SE7221BK1-E - Server Board - Mainboard

Бренд: Intel Страницы: 105

S875WP1 - EATX MBD 875 P4 DDR-2CH SATA RAID VID GETH

Бренд: Intel Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды