IBM i 830 Скачать руководство пользователя страница 482 | Manualshive

Страница: 482 / 1000

background image

e.

If no reference code appears, repeat steps a through d of this step
until you have checked all devices disconnected previously.

Continue to perform the initial program load (IPL).

This ends the procedure.

8.

Ensure that the following conditions are met:

v

The workstation addresses of all workstations on the failing port must be
correct.
Each workstation on the port must have a separate address, from 0 through
6. See the workstation service information if you need help with checking
addresses.

Did you find a problem with any of the above conditions?

Yes

No

↓

Go to step 11 of this procedure.

9.

Perform the following:

a.

Correct the problem.

b.

Select function 21 (Make DST Available).

c.

Check the console and any alternative consoles for a display.

Does a display appear on any of the consoles?

No

Yes

↓

Continue to perform the IPL.

This ends the procedure.

10.

Does the same reference code appear on the control panel?

Yes

No

↓

Go to “Starting Point for All Problems” on page 4 for this new
problem.

This ends the procedure.

11.

Is the reference code one of the following?: 0001, 0003, 0004, 0005, 0006, 0101,
0103, 0104, 0105, 0106, 5004, 5082, B000, D010, or D023.

No

Yes

↓

Go to step 15 of this procedure.

12.

Does the system have an alternative console on a second workstation IOP?

Yes

No

↓

Go to step 14 of this procedure.

13.

There is either a Licensed Internal Code problem, or there are two device
failures on the workstation IOPs, consoles, or cables. The console and any
alternative consoles are the most probable causes for this failure.

v

See the service information for the failing display to attempt to correct the
problem. If a display is connected to the system by a link protocol
converter, use the link protocol converter information to attempt to correct
the problem. The link protocol converter may be the failing item.

v

If you have another working display, you can exchange the console and
alternative consoles and perform an IPL to attempt to correct the problem.

Twinaxial Workstation PIPs

468

iSeries Model 830, 840, SB2, and SB3 Problem Analysis, Repair and Parts V5R1

«
...
480
481
482
483
484
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

NECCare Gold Express5800/320Fd

Бренд: NEC Страницы: 10

Бренд: NEC Страницы: 84

NEC Express5800 Series

Бренд: NEC Страницы: 6

eServer 130 xSeries

Бренд: IBM Страницы: 156

Virtual Services Platform 7000 Series

Бренд: Avaya Страницы: 103

FusionServer 1288H V5

Бренд: xFusion Digital Technologies Страницы: 96

Бренд: Sun Microsystems Страницы: 121

eserver xSeries 350

Бренд: IBM Страницы: 174

FileStore N8300

Бренд: Symantec Страницы: 55

Бренд: BITMAIN Страницы: 15

Бренд: Viavi Страницы: 11

Бренд: Promise Technology Страницы: 2

Бренд: AirLive Страницы: 113

Бренд: Adaptec Страницы: 6

Бренд: Intel Страницы: 70

Бренд: Intel Страницы: 179

Бренд: thomann Страницы: 60

Бренд: NetComm Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды