IBM i 830 Скачать руководство пользователя страница 921 | Manualshive

Страница: 921 / 1000

background image

Note:

If this password is not valid, ask the customer for the correct
password.

c.

Select the

Work with disk units

option on the Use Dedicated Service Tools

(DST) display.

d.

Select the

Work with disk unit recovery

option on the Work with Disk Unit

display.

e.

Select the

Restore disk unit data

option on the Work with Disk Unit

Recovery display.

f.

Enter the tape volume identifier. This is the volume identifier that you
entered during the save procedure.

g.

Install the first tape that the data was saved to in the tape unit.

h.

Select the tape unit that you want the data restored from on the Select
Tape Unit display.

i.

Select the disk unit that you want the data restored to on the Restore Disk
Unit Data display.

j.

Press F10 to confirm the restore.
The Function Status display shows the percent of customer data restored.

Note:

When the load-source disk is restored, the system automatically
performs an IPL to the Use Dedicated Service Tools (DST) display.
This occurs after the restore operation completes.

When all customer data from the tape to the disk restores successfully, the
display shows that the status of the restore operation is complete.

k.

Press the Enter key to complete the restore operation.

l.

Power off the system.

Note:

Any damaged objects that were restored must be loaded again by
the customer (have the customer see the

Backup and Recovery

information).

The system is ready for the next IPL.

This ends the procedure.

15.

Perform an IPL from removable media and select the option to install
Licensed Internal Code and recover configuration. (See “Installing Licensed
Internal Code” in the

iSeries Service Functions

information, which performs an

IPL and installs the Licensed Internal Code.)

16.

Did you get a Disk Configuration Error Report with a

″

Unit has incorrect

logical partition configuration

″

warning?

No

Yes

↓

You have logical partitions that need to be recovered before you can
continue with this disk unit recovery procedure. Perform the
following:

a.

Enter the Use Dedicated Service Tools (DST) option from the IPL
or Install the System display.

b.

Enter the password

22222222

.

Note:

If this password is not valid, ask the customer for the
correct password.

Data Recovery and General System Information

Chapter 6. Data Recovery Procedures and General System Information

907

«
...
919
920
921
922
923
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

Бренд: IBM Страницы: 84

Бренд: IBM Страницы: 110

8841 - eServer xSeries 236

Бренд: IBM Страницы: 100

Бренд: Advantech Страницы: 43

SuperServer 2028R-C1R(T)4+

Бренд: Supermicro Страницы: 1

Бренд: Zeiss Страницы: 12

Бренд: HP Страницы: 94

Integrity rx5670

Бренд: HP Страницы: 46

Бренд: HP Страницы: 98

NetServer AA 4000

Бренд: HP Страницы: 82

Бренд: HP Страницы: 25

HPE ProLiant ML30 Gen9

Бренд: HP Страницы: 112

Бренд: HP Страницы: 28

Бренд: HP Страницы: 56

Hyper Converged 380

Бренд: HP Страницы: 125

Бренд: HP Страницы: 23

integrity rx2800 i4

Бренд: HP Страницы: 156

Бренд: HP Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды