IBM i 830 Скачать руководство пользователя страница 108

Страница: 108 / 1000

Reference Code

Description/Action Perform all actions before exchanging Failing Items

Failing Item

4510

UPS Test Failure

UPSUNIT
TWRCARD

4513

UPS Interface Failure

UPSUNIT
TWRCARD

6018

One of the regulators has reported a fault

A regulator fault was detected.

PWRREG
BKSPCN

601A

One of the CPM regulators has reported a fault

A CPM regulator fault was detected.

PWRREG
BKSPCN
FI00030

6118

Regulator over current fault

One of the regulators detected an over current condition. This may be
caused by the regulator or one of cards powered by the regulator.

PWRREG
BKSPCN

6218

Regulator over current fault

Regulator 1 detected an over current condition. This may be caused by the
regulator or one of cards powered by the regulator.

PWRREG
BKSPCN

6238

Regulator over current fault

Regulator 2 detected an over current condition. This may be caused by the
regulator or one of cards powered by the regulator.

PWRREG
BKSPCN

6258

Regulator over current fault

Regulator 3 detected an over current condition. This may be caused by the
regulator or one of cards powered by the regulator.

PWRREG
ACMODUL

6318

Regulator Fault

Regulator 1 has reported a fault.

PWRREG
BKSPCN

631A

Regulator Fault

Regulator 1 has reported a fault.

PWRREG
ACMODUL
FI00030

6338

Regulator Fault

Regulator 2 reported a fault.

PWRREG
BKSPCN

633A

Regulator Fault

Regulator 2 reported a fault.

PWRREG
ACMODUL
FI00030

6358

Regulator Fault

A regulator 3 reported a fault.

PWRREG
ACMODUL

6400 to 6401

Power Good Fault

PGDPART
FI00065
BKSPCN

6518

One of the regulators has reported a fault

An over current sensor failure occurred for a regulator. The ac module or
one of the regulators can cause this fault.

PWRREG
BKSPCN

6618

Regulator over current fault

Regulator 1 reported a false over current condition.

Fault tolerance may allow continued system operation.

PWRREG
BKSPCN

1xxx

iSeries Model 830, 840, SB2, and SB3 Problem Analysis, Repair and Parts V5R1

Содержание i 830








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание i 830

Отзывы:

Похожие инструкции для i 830

Бренды по названию

Популярные бренды

IBM i 830, Руководство по ремонту

Результаты поиска

Содержание i 830

Отзывы:

Похожие инструкции для i 830

Бренды по названию

Популярные бренды