IBM i 830 Скачать руководство пользователя | Manualshive

Страница: 373 / 1000

background image

Ensure that the load-source disk unit is in device location 1.

This ends the procedure.

0019:

One or more disk units were formatted incorrectly.

The system will continue to operate normally. However, it will not operate at
optimum performance. To repair the problem, perform the following:

1.

Record the unit number and serial number of the disk unit that is formatted
incorrectly.

2.

Sign on to DST (see “Dedicated Service Tools (DST)” in the

iSeries Service

Functions

information).

3.

Select the

Work with disk units

option.

4.

Select the

Work with disk unit configuration

option.

5.

Select the

Remove unit from configuration

option.

6.

Select the disk unit you recorded earlier in this procedure.

7.

Confirm the option to remove data from the disk unit. This step may take a
long time because the data must be moved to other disk units in the auxiliary
storage pool (ASP)

8.

When the remove function is complete, select the

Add unit to configuration

option.

9.

Select the disk unit you recorded earlier in this procedure.

10.

Confirm the add. The disk unit is formatted during functional operation.

This ends the procedure.

001A:

The load-source disk unit data is down-level.

The load-source disk unit is mirror protected. The system is using the load-source
disk unit that does not have the current level of data.

1.

Select Manual mode and perform an IPL to DST (see “Dedicated Service Tools
(DST)” in the

iSeries Service Functions

information).

Does the Disk Configuration Error Report display appear?

Yes

No

↓

The system is now using the correct load-source.

This ends the procedure.

2.

Does a

Load source failure

message appear in the list?

Yes

No

↓

The system is now using the correct load-source.

This ends the procedure.

3.

Select option 5, then press F11, then press the Enter key to display details.
The load-source type, model, and serial number information that the system
needs is displayed on the console.
Is the load-source disk unit (displayed on the console) attached to an MSIOP
that cannot be used for a load-source?

Yes

No

↓

The load-source disk unit is missing. Go to step 1 for cause code 0002.

4.

Is the system configured for remote load-source protection?

LIC PIPs

Chapter 3. Problem Isolation Procedures (PIPs), Failing Items, and Symbolic FRU Isolation

359

«
...
371
372
373
374
375
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

Express5800/320Ma

Бренд: NEC Страницы: 86

Бренд: Zonet Страницы: 33

SuperServer E102-9W-C

Бренд: Supermicro Страницы: 103

ApplianceStor 15MT

Бренд: Rasilient Страницы: 30

Бренд: Axis Страницы: 66

SuperServer 6026TT-HIBQF

Бренд: Supero Страницы: 112

Бренд: Altos Страницы: 104

1-Port USB Print Server

Бренд: IBM Страницы: 15

PLATINIUM 9000-4R

Бренд: MAXDATA Страницы: 18

Бренд: Emerson Страницы: 23

DIXELL XWEB5000 PRO

Бренд: Emerson Страницы: 20

Бренд: Emerson Страницы: 18

Avocent ACS 6000

Бренд: Emerson Страницы: 93

Бренд: Emerson Страницы: 114

Centellis 2000 Shelf Release 3.0

Бренд: Emerson Страницы: 194

Бренд: Emerson Страницы: 222

Бренд: Cavalry Страницы: 16

Бренд: Syncronorm Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды