IBM i 830 Скачать руководство пользователя страница 943 | Manualshive

Страница: 943 / 1000

background image

status

″

of the other rows to see if there are any

″

failed

″

links,

other

than the

links that you recorded for the tower that you are working on.
Are there any

other

failed

links that are

not

associated with the tower that you

are working on?

Yes

No

↓

Go to step 12 of this procedure.

11.

Using table “Appendix F. HSL Loop Configuration and Status Form” on
page 963, look to see if there are any

operational

links between this tower and a

failed

link.

Are there any such

operational

links?

No

Yes

↓

You can

not

use this procedure to power off the tower. Doing so will

cause resources to be lost and a possible system failure. You

must

power down the system to continue working on this tower (see
“Powering On and Powering Off the System and Logical Partitions”

on page 922).

This ends the procedure.

12.

Examine table “Appendix F. HSL Loop Configuration and Status Form” on
page 963, to determine if the tower that you are working on is linked to an
SPD migrated tower (FC 5033, 5034, 5035, or 5077).
Is an SPD migrated tower (FC 5033, 5034, 5035, or 5077), the

next link

(leading or trailing) from the tower that you are working on?

No

Yes

↓

You can

not

use this procedure to power off the tower. Doing so will

cause a system failure. You

must

power down the system to continue

working on this tower (see “Powering On and Powering Off the
System and Logical Partitions” on page 922).

This ends the procedure.

13.

Are you working in a

FC 5079

expansion tower or unit?

No

Yes

↓

Power off

only

the expansion tower or unit (FC 5074) that you are

servicing.

Attention:

Only

one expansion tower inside the 1.8 meter rack may

be powered off at any given time!

Continue with step 14 of this procedure.

14.

Were you directed to power off the tower to set the SPCN configuration ID?

No

Yes

↓

Go to step 17 on page 930 of this procedure.

15.

Verify that the

″

type numbers

″

(ie; IOPs, IOAs, etc.) contained in the

expansion tower or unit that you are powering off, matches what is shown on
the system by performing the following:

a.

From the SST or DST menu, select the

Start a service tool

option.

b.

Select the

Hardware service manager

option.

c.

Select the

Packaging Hardware Resources (systems, frames, cards, etc.)

option.

Data Recovery and General System Information

Chapter 6. Data Recovery Procedures and General System Information

929

«
...
941
942
943
944
945
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

Бренд: IBM Страницы: 40

Бренд: IBM Страницы: 54

5big - Network NAS Server

Бренд: LaCie Страницы: 9

Бренд: LaCie Страницы: 14

MCX-2000 - MusicCAST Digital Audio Server

Бренд: Yamaha Страницы: 25

Бренд: Patton electronics Страницы: 121

SUPERSERVER 6035B-8R+

Бренд: Supero Страницы: 110

Бренд: Belkin Страницы: 8

Бренд: NetMedia Страницы: 2

Бренд: IBM Страницы: 75

IP-DECT SERVER 6500

Бренд: SpectraLink Страницы: 2

Бренд: SMART-AVI Страницы: 43

ANTMINER S19a Pro

Бренд: BITMAIN Страницы: 17

Бренд: Kramer Страницы: 28

Бренд: DSP4YOU Страницы: 28

ProxyServer MTPSR1-100

Бренд: Multitech Страницы: 54

Бренд: Supermicro Страницы: 76

Бренд: Supermicro Страницы: 79

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды