IBM i 830 Скачать руководство пользователя страница 338 | Manualshive

Страница: 338 / 1000

background image

↓

Verify that you have followed the power off, removal, installation
and power on procedures correctly. When you are sure that you
have followed the procedures correctly, then exchange the next FRU
in the list. If there are no more FRUs to exchange, then contact your
next level of support.

4.

Does the system/logical partition have mirrored protection?

Note:

If you do not know the type of protection on your system/logical
partition, select

Yes

.

Yes

No

↓

Go to step 6 of this procedure.

5.

From the Dedicated Service Tools (DST) display, select the

Work with disk units

option and resume mirrored protection for all units that have a suspended
status. (See “Work with Disk Unit Recovery” in the

iSeries Service Functions

information).

6.

From the Start a Service Tool display, select the

Hardware service manager

option and look for the I/O processors that have a failed or missing status.
Are all I/O processor cards operational?

Note:

Ignore any IOPs that are listed with a status of

not connected

.

No

Yes

↓

Go to step 12 of this procedure.

7.

Display the logical hardware resource information for the non-operational I/O
processors.
For all I/O processors and I/O adapters that are failing; record the bus
number (BBBB), board (bb) and card information (Cc).

8.

Perform the following:

a.

Return to the Dedicated Service Tools (DST) display.

b.

Display the Product Activity Log.

c.

Select the

All logs

option and search for an entry with the same bus, board,

and card address information as the non-operational I/O processor.

Note:

Do not include informational or statistical entries in your search.
Use only entries that occurred during the last IPL.

Did you find an entry for the SRC that sent you to this procedure?

No

Yes

↓

Ask your next level of support for assistance.

This ends the procedure.

9.

Did you find a B600 6944 SRC that occurred during the last IPL?

Yes

No

↓

A different SRC is associated with the non-operational I/O processor.

Go to “Chapter 2. Unit Reference Codes” on page 59 to correct the
problem.

This ends the procedure.

10.

Is there a B600 xxxx SRC that occurred during the last IPL other than the B600
6944 and informational SRCs?

Bus, High-Speed Link (HSL) PIPs

324

iSeries Model 830, 840, SB2, and SB3 Problem Analysis, Repair and Parts V5R1

«
...
336
337
338
339
340
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

Бренд: Vecow Страницы: 122

Bull Escala E5-700

Бренд: IBM Страницы: 116

Бренд: Xyplex Страницы: 58

Бренд: Vidyo Страницы: 186

Бренд: Abit Страницы: 56

SuperServer 2028R-C1R(T)4+

Бренд: Supermicro Страницы: 1

Бренд: IBM Страницы: 96

Бренд: Dell Страницы: 25

EMC PowerEdge R340

Бренд: Dell Страницы: 92

EMC PowerEdge R640

Бренд: Dell Страницы: 78

Бренд: Dell Страницы: 25

EMC PowerEdge R740

Бренд: Dell Страницы: 172

Бренд: Dell Страницы: 186

Бренд: Dell Страницы: 110

Бренд: Dell Страницы: 138

EMC Connectrix EC-1700 Series

Бренд: Dell Страницы: 110

EMC PowerEdge T440

Бренд: Dell Страницы: 156

EMC PowerEdge C6420

Бренд: Dell Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды