IBM i 830 Скачать руководство пользователя страница 402 | Manualshive

Страница: 402 / 1000

background image

Note:

If the system has logical partitions, perform this procedure only from the
Primary partition’s console and the system control panel.

1.

Ensure that the battery power unit is installed and that there was no system
power loss for the last 8 hours by checking the message log for CPF1816.

Note:

If the message log shows that a power loss occurred in the last 8 hours,
the battery may not be at full charge and the test may fail.

To check the message log, perform the following:

a.

Enter the command DSPLOG QHST

b.

Press F4 (prompt).

Note:

The

time date

parameter that you use should be for the last 8 hour

period.

c.

Fill in the time and date.
For the United States, the format is:
hhmmss mmddyy

Note:

The output may be printed (*PRINT) or displayed. The default (*) is to
display.

2.

Ensure that all user programs are ended.

3.

Perform the following:

a.

Ensure keystick is inserted and select Manual mode on the control panel.

b.

Select function 21 (Make DST Available) on the control panel.

c.

Press the Enter key.

d.

Enter the password on the DST Sign On display. You need the customer
password to get to the Use Dedicated Service Tools (DST) display.

4.

Select the

Start a Service Tool

option.

5.

Select the

System Power Control Network

option.

6.

Press the Enter key to continue.

7.

Select the

Test Battery Interface

option by entering

7

under the

OPT

column on

the line for the correct unit (

not

the line for the frame).

8.

Press the Enter key to confirm your selection.
Does the battery test complete with no problems found?

Yes

No

↓

Exchange the following, one at a time (see “Chapter 4. Removal and
Installation Procedures” on page 617 or the “Removal and Installation
Procedures” in the ):

a.

Battery power unit (see “BATRY” on page 505).

b.

Battery charger unit or UPSUNIT as installed.

c.

The SPCN card (TWRCARD).

d.

Backplane.

This ends the procedure.

9.

Approximately 24 hours from now, the system will perform a battery capacity
test. When the battery capacity test completes successfully, the battery power
unit test is complete.

This ends the procedure.

Power PIPs

388

iSeries Model 830, 840, SB2, and SB3 Problem Analysis, Repair and Parts V5R1

«
...
400
401
402
403
404
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

Бренд: IBM Страницы: 64

Univerge SV9100

Бренд: NEC Страницы: 78

UNIVERGE SL2100

Бренд: NEC Страницы: 34

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 975

Бренд: F5 Страницы: 72

x3100 M5 Type 5457

Бренд: IBM Страницы: 688

Бренд: LevelOne Страницы: 88

Бренд: Icy Box Страницы: 3

EonStor GS 3000 Series

Бренд: Infortrend Страницы: 134

Бренд: Kontron Страницы: 90

SuperServer 6029U-TR25M

Бренд: Supermicro Страницы: 151

Ultra Enterprise 3000

Бренд: Sun Microsystems Страницы: 48

PRIMERGY CX120 S1

Бренд: Fujitsu Страницы: 82

PRIMERGY BX922 S2

Бренд: Fujitsu Страницы: 106

PRIMERGY BX924 S3

Бренд: Fujitsu Страницы: 290

PRIMERGY BX924 S4

Бренд: Fujitsu Страницы: 286

PRIMERGY BX924 S3

Бренд: Fujitsu Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды