IBM i 830 Скачать руководство пользователя страница 491 | Manualshive

Страница: 491 / 1000

background image

DANGER

To prevent a possible electrical shock during an electrical storm, do not
connect or disconnect cables or station protectors for communications lines,
display stations, printers, or telephones. (RSFTD003)

DANGER

To prevent a possible electrical shock from touching two surfaces with
different electrical grounds, use one hand, when possible, to connect or
disconnect signal cables. (RSFTD004)

DANGER

To prevent a possible electrical shock, do not use the port tester during
electrical storms. (RSFTD006)

DANGER

To prevent power from switching on automatically during service procedures,
select manual or secure mode on the system unit control panel or disconnect
the cables that connect to J15 and J16 on the frame being serviced.
(RSFTD211)

Read and understand the following service procedures before using this section:

v

“Powering On and Powering Off the System and Logical Partitions” on page 922

v

“Determining a Primary or Alternative Console” in the

iSeries Service Functions

information

v

“Card Removal and Installation” in “Chapter 4. Removal and Installation
Procedures” on page 617.

v

“Locations and Addresses” on page 705

WSAC-PIP1

Note:

Determine if the system has logical partitions. Go to “Determining if the
System Has Logical Partitions” on page 943, before continuing with this
procedure.

Note:

If the system has logical partitions, perform this procedure from the logical
partition that reported the problem.

Read the “Overview” on page 476 before continuing with this procedure.

Note:

If the console has a keyboard error, there may be a K on the display. See the
workstation service information for more information.

1.

Ensure that your workstation meets the following conditions:

v

The workstation that you are using for the console is powered on.

v

The emulation program is installed and is working.

v

The input/output adapter (IOA) is installed and the workstation console
cable is attached.

Workstation Adapter Console PIPs

Chapter 3. Problem Isolation Procedures (PIPs), Failing Items, and Symbolic FRU Isolation

477

«
...
489
490
491
492
493
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

Бренд: Mako Страницы: 56

Бренд: NComputing Страницы: 95

Бренд: Xerox Страницы: 220

Бренд: Xerox Страницы: 28

DocuPrint 100MX

Бренд: Xerox Страницы: 2

EonServ 5000 Series

Бренд: Surveon Страницы: 33

Бренд: Patton electronics Страницы: 121

WECS II 2048/DMX/02

Бренд: Oase Страницы: 67

Бренд: TerraMaster Страницы: 13

Express5800/E120d-1

Бренд: NEC Страницы: 4

Express5800/B140a-T

Бренд: NEC Страницы: 19

Express5800/B120f-h

Бренд: NEC Страницы: 21

Express5800/GT110b

Бренд: NEC Страницы: 27

Express5800/GT110e-S

Бренд: NEC Страницы: 34

Express5800/B110d

Бренд: NEC Страницы: 19

Express5800/A2040d

Бренд: NEC Страницы: 20

Express5800/D120h

Бренд: NEC Страницы: 35

Express5800/A1040e

Бренд: NEC Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды