IBM i 830 Скачать руководство пользователя | Manualshive

Страница: 159 / 1000

background image

Reference Code

Description/Action Perform all actions before exchanging Failing Items

Failing Item

9320

Tape device Licensed Internal Code failure

Perform the following:

1.

Take a dump of the tape unit Licensed Internal Code (see the 3570 Tape
Unit service information).

2.

Power off the tape unit. Then power on the tape unit to resume
operation.

3.

Ask your next level of support for assistance.

FI00130
DHZDEV

9321

Gateway device Licensed Internal Code error

Use the gateway device service documenation to analyze the problem.

FCCODE

9350

Tape unit detected a read or write error on tape medium

A permanent read or write error occurred, and the tape unit determined
that the tape cartridge is defective. Exchange the tape cartridge.

MHZTMED
UHZCLN
DHZDEV

9351

Tape with excessive error rate was mounted in tape device.

The tape unit detected that the mounted tape cartridge has a history of
excessive read and write errors. It is recommended that you exchange the
tape cartridge.

MHZTMED
UHZCLN
DHZDEV

9355

The data format is incorrect; the tape cannot be read

The tape unit does not give support to the data format on the tape
cartridge. Use a different tape cartridge.

UHZUSER
MHZTMED
UHZCLN
DHZDEV

9500

I/O processor Licensed Internal Code error

If the system is operational, take a dump of the I/O processor data. For
more information, see the

iSeries Service Functions

information or ask your

next level of support for assistance.

FI00130

9800 to 9803

I/O processor successfully recovered from temporary error

No action required. This reference code is logged for information only.

9810

Problem analysis has determined a part should be replaced.

This reference code is used for ending Online Problem Analysis with a list
of failing items. (Information Only)

9899

Problem analysis completed, the problem has been corrected.

This reference code is used for ending Online Problem Analysis when no
problem was found or the problem was corrected.

UHZFIXD

9900

Licensed Internal Code for tape unit was not upgraded

The I/O processor loading of Licensed Internal Code (LIC) to the
programmable tape unit was not completed.

The tape unit will continue to operate with the previous LIC. You may do
either of the following:

v

Wait for next IPL when the system will attempt to load the LIC for the
tape drive again.

v

Perform “TU-PIP4” on page 453 to reset the IOP and the tape unit. When
the IOP is reset, if the device has the wrong level of LIC, the IOP will
attempt to load the new LIC.

UHZUSER

FFF6

Tape volume statistics logged (no action required)

3570

Chapter 2. Unit Reference Codes

145

«
...
157
158
159
160
161
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

Express 5800 Series

Бренд: NEC Страницы: 90

PDS-220F Series

Бренд: ICP DAS USA Страницы: 94

NECCare Gold Express5800/320Fd

Бренд: NEC Страницы: 10

Бренд: NEC Страницы: 84

NEC Express5800 Series

Бренд: NEC Страницы: 6

Бренд: Cabletron Systems Страницы: 93

Бренд: PaloAlto Networks Страницы: 30

Flex System x440 Compute Node

Бренд: IBM Страницы: 584

ApplianceStor 15MT

Бренд: Rasilient Страницы: 30

Бренд: IBM Страницы: 98

Бренд: IBM Страницы: 24

UltraNEXUS HD Blade

Бренд: Leightronix Страницы: 5

Бренд: QUANTA Страницы: 177

eserver xSeries 350

Бренд: IBM Страницы: 174

Бренд: QNAP Страницы: 39

Disk On-line Server NAS-2100

Бренд: QNAP Страницы: 112

Бренд: Planet Страницы: 93

SuperWorkstation 5049A-TR

Бренд: Supermicro Страницы: 189

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды