IBM i 830 Скачать руководство пользователя страница 353 | Manualshive

Страница: 353 / 1000

background image

Equipment such as air conditioners, copiers, and FAX machines should not
be attached to the same uninterruptable power supply, or motor generator
that the system is attached.

v

The system unit console and the Electronic Customer Support modem must
get AC voltage from the same uninterruptable power supply or motor
generator to which the system is attached.

This ends the procedure.

INT-PIP14 Station Protectors

Station protectors must be installed on all twinaxial cables that leave the building
in which the iSeries 400 system is located. This applies even if the cables go
underground, through a tunnel, through a covered outside hallway, or through a
skyway. Station protectors help prevent electrical noise on these cables from
affecting the iSeries 400 system.

1.

Look at the Product Activity Log to determine what workstations are associated
with the failure.

2.

Determine if station protectors are installed on the twinaxial cables to the
failing workstations.
Are station protectors installed on the twinaxial cables to the failing
workstations?

No

Yes

↓

Perform the next INT-PIP listed in the

INT-PIP

column.

This ends the procedure.

3.

You may need to install station protectors on the twinaxial cables to the failing
workstations. See chapter 9, section F in the

iSeries 400 Technical Information

Manual

, SY44-0008, for additional information on station protectors.

This ends the procedure.

INT-PIP16 Licensed Internal Code

Sometimes a dump of main storage is needed to analyze the problem. The data on
the dump is analyzed at the iSeries 400 system factory to determine the cause of
the problem and how to correct it.

1.

Copy the main storage dump to tape (see “Copying a Main Storage Dump” in
the

iSeries Service Functions

information).

2.

Ask your next level of support to determine if a Licensed Internal Code trouble
report (LICTR) needs to be written.

This ends the procedure.

INT-PIP18 PTFs Not Installed

One or more PTFs may be available to correct this specific problem.

1.

Ensure that all PTFs that relate to the problem have been installed.

Note:

Ensure that the latest IOP PTF has been installed before you exchange an
IOP card.

2.

Ask your next level of support for more information.

This ends the procedure.

INT-PIP20 Performance Problems

This procedure analyzes system performance problems.

1.

Look at the Product Activity Log and determine if any hardware errors
occurred at the same time that the performance problem occurred.

Intermittent PIPs

Chapter 3. Problem Isolation Procedures (PIPs), Failing Items, and Symbolic FRU Isolation

339

«
...
351
352
353
354
355
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

Бренд: Gateway Страницы: 138

QS21 - BladeCenter - 0792

Бренд: IBM Страницы: 110

NovaScale T820 F2

Бренд: Bull Страницы: 34

SuperServer 6026TT-HIBQF

Бренд: Supero Страницы: 112

Mobileraid MR8X

Бренд: Sans Digital Страницы: 81

Бренд: HIKVISION Страницы: 31

FusionServer XH321 V5

Бренд: xFusion Digital Technologies Страницы: 76

Бренд: Asus Страницы: 98

Бренд: Asus Страницы: 84

APOGEE Ethernet Microserver 2100

Бренд: Siemens Страницы: 2

Бренд: Siemens Страницы: 38

Бренд: Siemens Страницы: 40

RUGGEDCOM RS401

Бренд: Siemens Страницы: 50

Бренд: Siemens Страницы: 101

Бренд: Siemens Страницы: 116

Бренд: Siemens Страницы: 143

HiPath Xpressions

Бренд: Siemens Страницы: 278

Advanced Server UNIX V4.0

Бренд: Siemens Страницы: 365

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды