IBM i 830 Скачать руководство пользователя страница 173 | Manualshive

Страница: 173 / 1000

background image

Reference Code

Description/Action Perform all actions before exchanging Failing Items

Failing Item

9302

Tape device failure or media error

The tape unit detected a failure that may be caused by a hardware failure
or a media error.

Refer to the tape unit service information for possible information on
diagnositic tests that can be run to isolate between hardware and media
failures.

MH7TMED
FI00871

9303

Gateway device failure

Use the gateway device service documenation to analyze the problem.

FCGATE

9310

Licensed Internal Code for the tape unit is not correct

FI00130
FI00871

9320

Tape device Licensed Internal Code failure

FI00130
FI00871

9321

Gateway device Licensed Internal Code error

Use the gateway device service documenation to analyze the problem.

FCCODE

9350

Tape unit detected a read or write error on tape medium

A permanent read or write error occurred. Clean the tape unit and retry
the operation.

If cleaning the tape unit does not correct the problem, exchange the tape
media.

MH7TMED
UH7CLN
FI00871

9351

Tape with excessive error rate was mounted in tape device.

The tape unit detected that the mounted tape cartridge has a history of
excessive read and write errors. It is recommended that you exchange the
tape cartridge.

MH7TMED
UH7CLN
FI00871

9355

The data format is incorrect; the tape cannot be read

The tape unit has detected that the data format on the tape media is not
supported.

Clean the tape unit and retry the operation.

If the operation continues to fail, use a different tape cartridge.

UH7USER
MH7TMED
UH7CLN
FI00871

9500

I/O processor Licensed Internal Code error

If the system is operational, take a dump of the I/O processor data. For
more information, see the

iSeries Service Functions

information or ask your

next level of support for assistance.

FI00130

9800 to 9803

I/O processor successfully recovered from temporary error

No action required. This reference code is logged for information only.

9810

Problem analysis has determined a part should be replaced.

This reference code is used for ending Online Problem Analysis with a list
of failing items. (Information Only)

9899

Problem analysis completed, the problem has been corrected.

This reference code is used for ending Online Problem Analysis when no
problem was found or the problem was corrected.

UH7FIXD

63A0

Chapter 2. Unit Reference Codes

159

«
...
171
172
173
174
175
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

BladeCenter HS22

Бренд: IBM Страницы: 18

ML-2010 - B/W Laser Printer

Бренд: Samsung Страницы: 25

SEH InterCon PS54a-G

Бренд: SEH Страницы: 24

SuperServer 2028R-C1R(T)4+

Бренд: Supermicro Страницы: 1

PRIMERGY TX1310 M1

Бренд: Fujitsu Страницы: 66

Бренд: Fujitsu Страницы: 18

PRIMERGY TX1320 M1

Бренд: Fujitsu Страницы: 86

PRIMERGY TX120 S3

Бренд: Fujitsu Страницы: 82

PRIMERGY TX1310 M3

Бренд: Fujitsu Страницы: 68

PRIMERGY TX1310 M1

Бренд: Fujitsu Страницы: 232

PRIMERGY TX120 S2

Бренд: Fujitsu Страницы: 78

PRIMERGY TX1310 M5

Бренд: Fujitsu Страницы: 265

PRIMERGY TX1320 M1

Бренд: Fujitsu Страницы: 340

PRIMERGY TX120 S2

Бренд: Fujitsu Страницы: 60

PRIMERGY TX120 S3p

Бренд: Fujitsu Страницы: 8

Aspire EASYSTORE H341

Бренд: Acer Страницы: 59

Aspire EASYSTORE H341

Бренд: Acer Страницы: 74

Aspire EasyStore Series

Бренд: Acer Страницы: 148

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды