IBM i 830 Скачать руководство пользователя страница 375 | Manualshive

Страница: 375 / 1000

background image

3.

Select option 5 on the Incorrect Licensed Internal Code Install message line.
When the Display Incorrect Licensed Internal Code Install display appears on
the console, press the Enter key.

If the load-source disk unit in position 1 of the system unit does not contain the
correct level of Licensed Internal Code, restore the Licensed Internal Code to the
disk unit in position 1 of the system unit (see “Restoring Licensed Internal Code”
in the

iSeries Service Functions

information).

This ends the procedure.

0020:

The system appears to be a one disk unit system.

Select Manual mode and perform an IPL to DST (see “Dedicated Service Tools
(DST)” in the

iSeries Service Functions

information).

This ends the procedure.

0021:

The system password verification failed.

Select Manual mode and perform an IPL to DST (see “Dedicated Service Tools
(DST)” in the

iSeries Service Functions

information). You will be prompted for the

correct system password.

Enter the correct system password. If the correct system password is not available:

v

Select the

Bypass the system password

option from the prompt.

v

Have the customer contact the marketing representative immediately to order a
new system password from IBM.

This ends the procedure.

0022:

A different compression status was expected on a reporting disk unit.

Accept the warning. The reported compression status will be used as the current
compression status.

This ends the procedure.

0023:

There is a problem with a disk unit subsystem. As a result, there are

missing disk units in the system.

The system is capable of IPLing in this state.

Perform the following:

1.

Select DST using Function 21 (see “Control Panel Functions” in the

iSeries

Service Functions

information).

2.

On the Service Tools display, select the

Start a Service Tool

option (see the

iSeries

Service Functions

).

3.

Select the

Product activity log

option on the Start a Service Tool display.

4.

Select the

Analyze log

option on the Product Activity Log display.

5.

On the Select Subsystem Data display, select the option to view All Logs.

Note:

You can change the From: and To: Dates and Times from the 24 hour
default if the time that the customer reported having the problem was
more than 24 hours ago.

LIC PIPs

Chapter 3. Problem Isolation Procedures (PIPs), Failing Items, and Symbolic FRU Isolation

361

«
...
373
374
375
376
377
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

ColorPASS-Z5000

Бренд: Canon Страницы: 130

HS12 - BladeCenter - 8028

Бренд: IBM Страницы: 204

Бренд: MSI Страницы: 54

Бренд: Advantech Страницы: 96

@server xSeries 343

Бренд: IBM Страницы: 193

Бренд: NASdeluxe Страницы: 6

ZXCLOUD R5300 G3

Бренд: Zte Страницы: 19

Netra SPARC T3-1BA

Бренд: Sun Oracle Страницы: 62

Бренд: Sun Oracle Страницы: 182

Бренд: Sun Oracle Страницы: 222

Бренд: Sun Microsystems Страницы: 114

Бренд: Sun Microsystems Страницы: 192

Бренд: Sun Microsystems Страницы: 270

Бренд: Lantronix Страницы: 135

@server iSeries

Бренд: IBM Страницы: 294

Бренд: Optibase Страницы: 156

5325301728 - Snap Server 4200 NAS

Бренд: Adaptec Страницы: 42

Бренд: 10ZiG Technology Limited Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды