IBM i 830 Скачать руководство пользователя страница 596 | Manualshive

Страница: 596 / 1000

background image

REM_SYS

A problem has occurred in a remote system that is in an HSL OptiConnect loop.
The Service Action Log (SAL) code will attempt to identify the HSL loop number
of the local system and the serial number of the remote system as a portion of the
part description for this symbolic FRU. If the SAL could not identify the serial
number of the remote system then check all the systems which are connected to
the local HSL loop identified in the SAL. Search the SAL of the remote system(s)
for hardware and LIC problems. Correct any problems you find with LIC or
Network Interface Controller (NIC) hardware.

This ends the procedure.

RIOPORT

The system processor has detected an error on the HSL port.

Use the information in the Location column of the Reference Code table and the
information from “Locations and Addresses” on page 705 to determine the physical
mapping of the information from the Location column.

Check the cabling and connections from the failing item location. Follow the
procedure in Symbolic FRU “SIRGCBL” on page 588.

RMDEV

A removable media power regulator or device in a migrated expansion tower may
be failing.

See the RMDEV symbolic FRU in the

Migrated Expansion Tower Problem Analysis,

Repair and Parts

for FRU isolation instructions.

SIADPCD

SIADPCD: High Speed Link I/O bridge card.

The failing component is the HSL I/O bridge card in a system unit base I/O tower,
a FC 5074, FC 5078/0578, or FC 5079 (1.8m expansion tower) I/O expansion tower,
or the Integrated xSeries Adapter Card in an xSeries server.

1.

If you a working from the Service Action Log and you know the frame ID
where this failing component is located, then continue with the next step in this
procedure. Otherwise, record the bus number value (BBBB) in word 7 of the
SRC, see “Breaking Down The SRC” on page 280 for help in determining the
bus number. Search for the bus number in HSM or the System Configuration
Listing to determine which frame or I/O tower contains the failing component.

2.

Determine the tower type where the failing component is located and exchange
the FRU indicated using the links to the service information for that FRU.

Symbolic FRUs

582

iSeries Model 830, 840, SB2, and SB3 Problem Analysis, Repair and Parts V5R1

«
...
594
595
596
597
598
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

Бренд: IBM Страницы: 64

Бренд: Vxl Страницы: 2

AirLive WP-203G

Бренд: Ovislink Страницы: 132

Transport TX46 (B4985) Service

Бренд: TYAN Страницы: 75

Бренд: Buffalo Страницы: 2

Бренд: Olive Страницы: 24

System x3550 M3

Бренд: IBM Страницы: 160

System x3650 M4 Type 7915

Бренд: IBM Страницы: 192

Бренд: IBM Страницы: 694

System x3755 M3 7164

Бренд: IBM Страницы: 126

Бренд: Fujitsu Страницы: 280

HAM RADIO DELUXE

Бренд: Kenwood Страницы: 16

Бренд: dallmeier Страницы: 12

Бренд: XtendLan Страницы: 28

Бренд: DSP4YOU Страницы: 28

Бренд: Kathrein Страницы: 20

GV-Video Server

Бренд: GeoVision Страницы: 179

ZXCLOUD iBOX CT320

Бренд: Zte Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды