IBM i 830 Скачать руководство пользователя страница 556 | Manualshive

Страница: 556 / 1000

background image

d.

The Configuration ID should now be displayed for the non-system unit.
For a system unit, use the arrow keys to increment/decrement the
sub-function field to display the configuration ID for the CEC.

The Configuration ID displayed is defined as follows:

80

FC 5065/5066

81

FC 5074/5079, FC 8079 (002)

82

FC 9079 (On Model 840), FC 8079 (001)

83

FC 9074 (On Model 830)

84

FC 5078/0578

90

FC 5075

Is the correct configuration ID displayed for the tower selected?

No

Yes

↓

Go to 17 on page 543 of this procedure.

15.

Perform the following to set frame Configuration ID:

Note:

The System or Frame that the ID is being set on MUST be powered
down with AC applied.

a.

Select Function 07 on the system control panel. Press Enter. (07** will be
displayed)

b.

Use the arrow keys to increment/decrement to sub-function A9. (07A9 will
be displayed). Press Enter. (07A9 00 will be displayed)

c.

Use the arrow keys to increment / decrement to the frame address of the
box you want to set the Configuration ID (usually 02, 03, etc. for the
towers, 01 for system unit frames). (07nn will be displayed where nn is the
frame address) Press Enter. (07nn 00 will be displayed)

Note:

The display on the addressed frame should now be blinking on and
off (Non-system unit only).

d.

Select the correct Configuration ID from the following table:

80

FC 5065/5066

81

FC 5074/5079, FC 8079 (002)

82

FC 9079 (On Model 840), FC 8079 (001)

83

FC 9074 (On Model 830)

Figure 12. Control PANEL DIAGRAM FOR FUNCTION A8:

Symbolic FRUs

542

iSeries Model 830, 840, SB2, and SB3 Problem Analysis, Repair and Parts V5R1

«
...
554
555
556
557
558
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

Бренд: ExtraHop Страницы: 5

Бренд: SEH Страницы: 20

Digital Audio Server

Бренд: CAAS Audio Страницы: 23

SuperWorkstation 740A-T

Бренд: Supermicro Страницы: 138

301297U - 1TB Ethernet Disk XP Embedded Network Attached...

Бренд: LaCie Страницы: 67

Бренд: Conceptronic Страницы: 127

Бренд: HIKVISION Страницы: 13

DocuColor 45087638

Бренд: Xerox Страницы: 28

Бренд: Data-Tronix Страницы: 29

Бренд: Data-Tronix Страницы: 30

Бренд: Asus Страницы: 186

Бренд: Bodet Страницы: 13

Advanced Office-in-a-Box

Бренд: Enconnex Страницы: 40

Бренд: Viavi Страницы: 8

Бренд: TRENDnet Страницы: 2

Бренд: TRENDnet Страницы: 2

TEW-P1UG - Wireless Print Server

Бренд: TRENDnet Страницы: 2

Бренд: TRENDnet Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды