IBM i 830 Скачать руководство пользователя страница 382 | Manualshive

Страница: 382 / 1000

background image

The system is using the IASP configuration source disk unit that does

not

have the

current level of data.

Work with the customer to recover the configuration. Use a workstation with
Operations Navigator installed to select the disk pool with the problem, and then
select the recover configuration option for this disk pool.

This ends the procedure.

002E:

The Independent ASP is assigned to another system or a Licensed Internal

Code program error occurred. Work with the customer to check other systems to
determine if the Independent ASP has been assigned to it. If the Independent ASP
has not been assigned to another system, ask your next level of support for
assistance.

This ends the procedure.

002F:

The system version and release are at a different level than the IASP version

and release.

The system version and release must be upgraded to be the same as the system
version and release in which the IASP was created.

This ends the procedure.

0030:

The mirrored IASP configuration source disk unit has a disk configuration

status of

unknown

and is missing from the disk configuration.

Go to step 1 for cause code 0002.

0032:

A Licensed Internal Code program error occurred.

Ask your next level of support for assistance.

This ends the procedure.

0099:

A Licensed Internal Code program error occurred.

Ask your next level of support for assistance.

This ends the procedure.

LIC-PIP13

Note:

Determine if the system has logical partitions. Go to “Determining if the
System Has Logical Partitions” on page 943, before continuing with this
procedure.

Note:

If the system has logical partitions, perform this procedure from the logical
partition that reported the problem.

Note:

Do not power off the system when performing this procedure.

A disk unit seems to have stopped communicating with the system. The system
has stopped normal operation until the cause of the disk unit failure can be found
and corrected.

LIC PIPs

368

iSeries Model 830, 840, SB2, and SB3 Problem Analysis, Repair and Parts V5R1

«
...
380
381
382
383
384
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

ColorPASS-Z5000

Бренд: Canon Страницы: 130

Бренд: 360 Systems Страницы: 8

8BIG RACK THUNDERBOLT 2

Бренд: LaCie Страницы: 28

Бренд: Ganz Страницы: 5

Бренд: 7starlake Страницы: 32

Netfinity 1000-8477 21Y

Бренд: IBM Страницы: 268

Бренд: SmartSight Страницы: 113

2622W-P - annexe 1

Бренд: SMC Networks Страницы: 83

Бренд: Multitech Страницы: 35

Бренд: Black Box Страницы: 46

Бренд: BushkaBlue Страницы: 30

DIRECTORY SERVER 7.1 SP7 - S

Бренд: Red Hat Страницы: 12

SafeNet ProtectServer PCIe HSM

Бренд: Gemalto Страницы: 17

Бренд: Adaptec Страницы: 6

Бренд: D-Link Страницы: 146

Sun Fire X4470M2

Бренд: Oracle Страницы: 60

Бренд: Melco Страницы: 79

AcquiSuite A8810

Бренд: Obvius Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды