IBM i 830 Скачать руководство пользователя страница 184 | Manualshive

Страница: 184 / 1000

background image

Reference Code

Description/Action Perform all actions before exchanging Failing Items

Failing Item

9202

Tape unit failed after Licensed Internal Code was loaded

Before exchanging any parts, do the following:

1.

Ensure that the device is powered on.

2.

Ensure that the SCSI cable between the device and the I/O Processor or
I/O Adaptor is seated correctly, and that there are not bent or damaged
pins on the SCSI cable.

3.

Ensure that the terminating plug is attached to the device.

46G2227
46G3934
FI00830
FI00131
46G2599
17G1500
42F7300

9210

Illegal or unsupported tape unit response

46G2227
FI00130
FI00131

9300

Tape unit failure

The tape drive reported a hardware error to the IOP; the amber light on
the tape drive may be blinking.

Perform “TU-PIP2” on page 448.

46G2227
ML2TMED
46G3934
42F7300

9301

Tape device failure, redundancy lost

The tape device detected a hardware failure that does not prevent the tape
unit from completed the current operation.

Refer to the Tape unit service information to determine the failing item.

46G2227
ML2TMED
46G3934
42F7300

9302

Tape device failure or media error

The tape unit detected a failure that may be caused by a hardware failure
or a media error.

Refer to the tape unit service information for possible information on
diagnostic tests that can be run to isolate between hardware and media
failures.

ML2TMED
46G2227
46G3934
42F7300

9310

Licensed Internal Code for the tape unit is not correct

46G2227
FI00130

9320

Tape device Licensed Internal Code failure

FI00130
46G2227

9350

Tape unit detected a read or write error on tape medium

A permanent read or write error occured. Clean the tape unit and retry the
operation.

If cleaning the tape unit does not correct the problem, exchange the tape
media.

ML2TMED
46G2227
46G3934
42F7300

9351

Tape with excessive error rate was mounted in tape device.

The tape unit detected that the mounted tape cartridge has a history of
excessive read and write errors. It is recommended that you exchange the
tape cartridge.

ML2TMED
UL2CLN
46G2227

9355

The data format is incorrect; the tape cannot be read

The tape unit has detected that the data format on the tape media is not
supported.

Clean the tape unit and retry the operation.

If the operation continues to fail, use a different tape cartridge.

UL2USR1
ML2TMED
UL2CLN
46G2227

7208

170

iSeries Model 830, 840, SB2, and SB3 Problem Analysis, Repair and Parts V5R1

«
...
182
183
184
185
186
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

88631SU - System x3850 - 8863

Бренд: IBM Страницы: 90

Бренд: AIC Страницы: 88

Vlinx VESR4 4 Series

Бренд: B&B Electronics Страницы: 70

Бренд: Qeedji Страницы: 58

Бренд: Rohde & Schwarz Страницы: 126

Бренд: IBM Страницы: 75

Бренд: D-Link Страницы: 40

Бренд: Asus Страницы: 82

Бренд: Asus Страницы: 32

Бренд: Asus Страницы: 42

RS100-E5 - 0 MB RAM

Бренд: Asus Страницы: 148

PIKE II 3008 Series

Бренд: Asus Страницы: 80

Бренд: Asus Страницы: 44

Бренд: Asus Страницы: 56

Бренд: Asus Страницы: 40

Бренд: Asus Страницы: 20

Pentium 4 1U Rackmount Server AP160R-S

Бренд: Asus Страницы: 46

Бренд: Asus Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды