IBM i 830 Скачать руководство пользователя страница 669 | Manualshive

Страница: 669 / 1000

background image

Models 830/SB2 with FC 9074 – Battery (T01 through T04)

Attention:

Removing the battery power unit while the system is running on

battery power will cause the system to fail and may damage the battery power
unit and the card enclosure.

1.

If the system is powered on,

you do not have to power off the system

to

perform this procedure.

2.

Remove the rear cover (see “Models 830/SB2 with FC 9074 – Covers” on
page 663).

Refer to “Models 830 and SB2 with FC 9074 - Final Assembly, Rear” on page 820
and perform the following steps.

3.

Remove the EMC access plate that covers the battery packs.

4.

Remove the mounting screw from the battery pack that you are replacing.

5.

Remove the battery pack.

CAUTION:
The weight of this part or unit is between 18 and 32 kilograms (39.7 and 70.5
pounds). It takes two persons to safely lift this part or unit. (RSFTC204)

CAUTION:
The battery is a lead-acid battery. To avoid possible explosion, do not burn.
Exchange only with the IBM-approved part. Recycle or discard the battery as
instructed by local regulations.

In the United States, IBM has a process for the collection of this battery. For
information, call 1-800-426-4333. Have the IBM part number for the battery unit
available when you call. (RSFTC225)

6.

Install the battery pack by reversing the removal procedure. After exchanging
an item, go to “Verifying the Repair” on page 920.

Note:

After you install the new battery, use HSM to perform a battery test to
ensure correct operation.

This ends the procedure.

Models 830/SB2 with FC 9074 – Cards – Concurrent

Attention:

If removing the cover while powered on, errors may occur due to

Electromagnetic Interference.

Attention:

All cards are sensitive to electrostatic discharge (see “Appendix C.

Working with Electrostatic Discharge-Sensitive Parts” on page 955).

CAUTION:
The circuit card contains lead solder. To avoid the release of lead (Pb) into the
environment, do not burn. Discard the circuit card as instructed by local
regulations. (RSFTC234)

In some cases you do not need to power down the system in order to change PCI
cards. Use the following rules to determine if you should use dedicated or
concurrent removal and installation procedures. If you use concurrent maintenance

Remove and Replace Procedures

Chapter 4. Removal and Installation Procedures

655

«
...
667
668
669
670
671
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

TS-U100 - NAS Server - USB

Бренд: TRENDnet Страницы: 47

x3105 - System - 4347

Бренд: IBM Страницы: 130

System x3650 Type 7979

Бренд: IBM Страницы: 194

Бренд: SEH Страницы: 32

Бренд: Planet Страницы: 90

Бренд: Supero Страницы: 98

Бренд: 3Com Страницы: 65

Бренд: Acnodes Страницы: 5

Бренд: Riva Страницы: 20

Бренд: Gateway Страницы: 24

Sun Fire X2270 M2

Бренд: Oracle Страницы: 100

Бренд: Gigabyte Страницы: 24

Бренд: Inspur Страницы: 2

301417U - Big Disk Network NAS Server

Бренд: LaCie Страницы: 48

Бренд: IBM Страницы: 622

TotalStorage FAStT600

Бренд: IBM Страницы: 134

CE-HE130S2 Series

Бренд: Ablecom Страницы: 43

Portal Server ETV v4.2.1

Бренд: VBrick Systems Страницы: 180

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды