IBM i 830 Скачать руководство пользователя | Manualshive

Страница: 930 / 1000

background image

24.

From the Use Dedicated Service Tools (DST) display, perform the following to
format and initialize the disk drive you installed in step 22 of this procedure:

a.

Select the

Work with disk units

option on the Use Dedicated Service Tools

(DST) display.

b.

Select the

Work with disk unit recovery

option on the Work with Disk Units

display.

c.

Select the

Disk unit problem recovery procedures

option on the Work with

Disk Unit Recovery display.

d.

Select the

Initialize and format disk unit

option on the Problem Recovery

Procedures display.

e.

Select the non-configured disk unit you installed in step 22 of this
procedure as the unit to work with.

f.

Verify the initialization and formatting by pressing F10. The initialization
and formatting may take 30 minutes or longer to complete.

g.

Return to the Work with Disk Unit Recovery display.

25.

Perform the following to copy data from the failing disk drive to the disk
drive you installed in step 22 on page 915 of this procedure:

a.

Select the

Copy disk unit data

option on the Work with Disk Unit Recovery

display.

b.

Select the failing unit as the unit to copy.

c.

Select the non-configured unit you installed in step 22 on page 915 of this
procedure as the unit to copy to.

d.

The console displays the percent of the data copied. If the number of
unreadable pages displays, write down the number of unreadable pages.
You will use the number of unreadable pages later in this procedure.

e.

Wait until the status of the copy is

Complete

. Customer data is not

recoverable if one of the following occurs:

v

The copy operation does not complete.

v

There is a large number of unreadable pages to copy from the disk unit.

Continue with the next step of this procedure.

26.

Perform the following to remove the failing disk unit on the system:

a.

Power off the system.

b.

Find the failing disk unit. Slide the disk unit out of the system.

27.

Perform the following to move the new disk unit into the location that held
the failing disk unit:

a.

Remove the new disk unit from the location you found in step 21 on
page 915 of this procedure. Be very careful with the disk unit. It contains
the disk unit data.

b.

Install the new disk unit into the location that contained the failing disk
unit. You removed the failing disk unit in step 26 of this procedure.

28.

Install the disk unit you removed in step 22 on page 915 of this procedure.

29.

Were any pages unreadable during the copy operation?

No

Yes

↓

Some objects may be damaged. The customer may have to load the
damaged objects again. Have the customer see the

Backup and Recovery

information.

This ends the procedure.

Data Recovery and General System Information

916

iSeries Model 830, 840, SB2, and SB3 Problem Analysis, Repair and Parts V5R1

«
...
928
929
930
931
932
...
»

Содержание i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i 830

ColorPASS-Z5000

Бренд: Canon Страницы: 130

8835 - Eserver 325 - 1 GB RAM

Бренд: IBM Страницы: 68

Бренд: IBM Страницы: 42

eServer BladeCenter HS20Type 8832

Бренд: IBM Страницы: 158

Бренд: Abit Страницы: 56

Бренд: Intermec Страницы: 232

S7000FC4UR - Server System - 0 MB RAM

Бренд: Intel Страницы: 13

Alcatel-Lucent OXO Connect Compact

Бренд: Nokia Страницы: 216

Бренд: Viavi Страницы: 11

Бренд: Viavi Страницы: 4

Бренд: Super Страницы: 60

Бренд: Viavi Страницы: 12

Бренд: Vitek Страницы: 55

Бренд: Inspur Страницы: 147

Бренд: ICPDAS Страницы: 104

AS2041M-32R Plus

Бренд: Supero Страницы: 106

Бренд: 3Com Страницы: 65

QuantaGrid S31A-1U

Бренд: QUANTA Страницы: 159

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды