background image

W131-X30 Quick Installation Guide

Pre-installation Cautions

 

Make sure the system is not turned on or connected to AC power.

 

Always handle boards carefully. They can be extremely sensi-tive to electrostatic discharge (ESD). Hold boards only by their edges. 

 

After removing a board from its protective wrapper or from the system, place the board component side up on a grounded, static free surface. 

 

Use a conductive foam pad if available but not the board wrapper. Do not slide board over any surface.

 

Risk of explosion if battery is replaced incorrectly or with an incorrect type. Replace the battery only with the same or equivalent type recommended 

 

by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

No.  

Code 

 

Description

1   

MLAN   

Server managemnt LAN port 

2   

USB2_LAN1 

LAN port #1 (top) / USB 3.0 ports (bottom) 

3   

USB2_LAN2 

LAN port #2 (top) / USB 3.0 ports (bottom)  

4   

COM1_VGA 

Serial port (top) / VGA port (bottom)

5   

PMBUS   

PMBus connector 

6   

SYS_FAN1 

System fan connector#1

7   

P12V_AUX 

8 pin power connector (for CPU)

8   

CPU_FAN 

CPU fan connector 

9   

SYS_FAN2 

System fan connector#2

10   

ATX1 

 

24 pin main power connector

11   

SD_CN   

SD card connector

12   

SATA_4   

SATA 3 6Gb/s connector

13   

SATA_5   

SATA 3 6Gb/s connector

14   

SATA_2   

SATA 3 6Gb/s connector

15   

SATA_3   

SATA 3 6Gb/s connector

16   

SATA_1   

SATA 3 6Gb/s connector

17   

SATA_0   

SATA 3 6Gb/s connector

18   

FP_2 

 

Secondary front panel header  

 

19   

FP_1 

 

Front panel header

20   

F_USB2   

USB 2.0 header

21   

IPMB   

IPMB connector

22   

TPM 

 

TPM connector

23   

BP_1 

 

HDD back plane board header

24   

COM2   

Serial port cable connector

25   

PCIE_1   

PCI Express x8 slot (running at x4)

26   

PCIE_2    

PCI Express x16 slot (running at x8)

27   

BAT 

 

Battery socket

28   

PCIE_3   

PCI Express x1 slot

29   

PCIE_4   

PCI Express x16 slot (running at x8) 

30   

LED_BMC1 

BMC firmware readiness LED

Motherboard Components

1

2

3

4

5

6
7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

30

25 26 28

27

29

ME

Force

Update

ME_UPDATE

Default
Enable

3

2

1

Clear

CMOS

CLR_CMOS

Enable

Default

S3 

Power On

Select

S3_MASK

3

2

1

Default
Enable

Password 

Clear

BIOS_PWD

Default Enable

1 2 3

Default Enable

1 2 3

ME

Recovery

ME_RCVR

Default Enable

1 2 3

BIOS

Recovery

BIOS_RCVR

CPU

DIMM_P0_A0
DIMM_P0_A1
DIMM_P0_B0
DIMM_P0_B1

System Components

Front Bezel Door

2

3

4

5

6

3

1

No.   Desription

1   

Optical disc drive (Option)

2   

Front bezel door

3   

Hard Disk Drives

4   Motherboard

5   

PCIe card bay

6   

Power supply module

System Cover

1

1

2

3

1

2

PCI Express Card

Power Supply 

1

2

Hard Disk Drive

Optical Disc Drive 

1

2

1

2

1

2

Installing CPU/

安装

CPU

1

2

NOTE!

Remove side cover before removing 

the front bezel door

Memory Population Configuration/

安装内存

 

All channels in system run at the fastest common frequency.

 

Mixing ECC and non-ECC UDIMMs anywhere on the platform is not supported.

 

1 and 2 DPC is supported at 2133MHz.

 

所有通道模式以最快的频率速度运行。

 

此主板不支持ECC与非ECC内存模组混合使用。

 

 2 DPC 

均支持

2133MHz

速度

Type

Ranks Per

DIMM and 

Data Width

Speed (MT/s); 

Slot Per Channel (SPC) and 

DIMM Per Channel (DPC)

Supported

Voltage

2 Slot Per Channel

1DPC

2DPC

UDIMM

Unbuffered

DDR4 ECC

UDIMM

Unbuffered

DDR4 non-ECC

SR

1.2V

1.2V

2133

2133

DR

2133

2133

No.   Desription

1   

USB 2.0 ports

2   

Power button with LED

No.   Desription

1   

Power supply module cord socket

2   

Serial port

3   

VGA port

4   

USB 3.0 ports

5   

GbE LAN ports

6   

10/100/1000 Server management LAN port

7   

PCIe card bay

System Appearance

Off

State

Description

Yellow On

1Gbps data rate

Green On

100Mbps data rate

10Mbps data rate

10/100/1000 LAN LED:

Speed LED Link/Activity 

LED

1

2

1

2
3

4
5
6

7

Power button/ LED:

Green On

Off

Description

System is powered on.

System is not powered on or in ACPI S5 state (power off)

System is in ACPI S4 state (hibernate mode)

State

PN:12xx

Отзывы: