manualshive.com logo in svg

Gestetner G060, Руководство по обслуживанию

Поделиться
Скачать
Gestetner G060 Скачать руководство пользователя страница 999

 

SC TABLE 

SM 4-37 

G570 

 

SC 800 
(CF) 

Startup without 
video output end 
error (K) 
 

Video transfer to the engine 
is started, but the engine 
does not issue a video 
transmission end command 
within the specified time. 

• 

Defective BCU 

 

1. Turn the main switch off and on. 
2. Check the cable connection. 
3. Replace the BCU. 

B 

SC 801 
(CF) 

Startup without 
video output end 
error (Y) 
 

Video transfer to the engine 
is started, but the engine 
does not issue a video 
transmission end command 
within the specified time. 

• 

Defective BCU 

 

1. Turn the main switch off and on. 
2. Check the cable connection. 
3. Replace the BCU. 

B 

SC 802 
(CF) 

Startup without 
video output end 
error (M) 
 

Video transfer to the engine 
is started, but the engine 
does not issue a video 
transmission end command 
within the specified time. 

• 

Defective BCU 

 

1. Turn the main switch off and on. 
2. Check the cable connection. 
3. Replace the BCU. 

B 

SC 803 
(CF) 

Startup without 
video output end 
error (C) 
 

Video transfer to the engine 
is started, but the engine 
does not issue a video 
transmission end command 
within the specified time. 

• 

Defective BCU 

 

1. Turn the main switch off and on. 
2. Check the cable connection. 
3. Replace the BCU. 

B 

SC 804 

(CF) 

Video input 
incomplete (K) 

SC 805 

(CF) 

Video input 
incomplete (Y) 

SC 806 

(CF) 

Video input 
incomplete (M) 

SC 807 

(CF) 

Video input 
incomplete (C) 

SC 808 

(CF) 

Video input 
incomplete (R) 

SC 809 

(CF) 

Video input 
incomplete (G) 

SC 810 

(CF) 

Video input 
incomplete (B) 

• 

The scanner is requested 
to transfer video data, but 
does not issue the video 
transmission end 
command within the 
defined time. 

• 

Board connector 
between controller 
and bridge board 
loose 

• 

Board connector 
between bridge board 
and IPU loose 

• 

IPU board defective 

• 

Controller board 
defective 

• 

Bridge board 
defective 

 

1. Turn the main switch off and on. 
2. Check the cable connection between 

controller and bridge board. 

3. Check the cable connection between 

bridge board and IPU. 

4. Replace the IPU board. 
5. Replace the controller board. 
6.  Replace the bridge board. 

B 

Rev. 09/2003 

⇒

⇒

⇒

⇒

Содержание G060



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды