Gestetner G060 Скачать руководство пользователя страница 614 | Manualshive

Страница: 614 / 1106

Gestetner G060 Скачать руководство пользователя страница 614

SCANNER SP

G570

5-76

SM

2

Mode Number

(Class 1, 2, and 3)

Function / [Setting]

18

Notch No.3: Contrast

Adjusts the image density for each image
density level for Text mode when using binary
picture processing mode.
[ 0 to 255 / 128 / 1/step ] DFU

19

Notch No.3: Threshold

[ 0 to 255 / 100 / 1/step ] DFU

20

Notch No.2:
Brightness

[ 0 to 255 / 128 / 1/step ] DFU

21

Notch No.2: Contrast

[ 0 to 255 / 128 / 1/step ] DFU

22

Notch No.2: Threshold

[ 0 to 255 / 85 / 1/step ] DFU

23

Notch No.1(Darker):
Brightness

[ 0 to 255 / 128 / 1/step ] DFU

24

Notch No. 1(Darker):
Contrast

[ 0 to 255 / 128 / 1/step ] DFU

002

25

Notch No. 1(Darker):
Threshold

*

NV

[ 0 to 255 / 70 / 1/step ] DFU

[Text/Photo mode settings]

1

MTF Filter Coefficient
(Main scan)

Selects the MTF filter coefficient in the main
scan direction for Text/Photo mode.
Select a higher number for a stronger filter.
If this is “0”, the MTF filter is not applied.
[ 0 to 15 / 4 / 1/step ] DFU

2

MTF Filter Coefficient
(Sub scan)

As above, for sub scan
[ 0-13 / 4 / 1/step ] DFU

3

Smoothing Filter

Selects the smoothing pattern for Text/Photo
mode when using binary picture processing
mode.
A larger value could cause moiré to appear in
the image.
[ 0 to 7 / 0 / 1/step ] DFU

4

Scanner Gamma

Selects the scanner gamma type for Text/Photo
mode when using binary picture processing
mode.
[ 0 to 6 / 5 / 1/step ] DFU

5

Notch No.7(Lighter):
Brightness

Adjusts the image density for each image
density level for Text mode when using binary
picture processing mode.
[ 0 to 255 / 128 / 1/step ] DFU

6

Notch No.7(Lighter):
Contrast

[ 0 to 255 / 128 / 1/step ] DFU

7

Notch No.7(Lighter):
Threshold

[ 0 to 255 / 160 / 1/step ] DFU

8

Notch No.6:
Brightness

[ 0 to 255 / 128 / 1/step ] DFU

9

Notch No.6: Contrast

[ 0 to 255 / 128 / 1/step ] DFU

10

Notch No.6: Threshold

[ 0 to 255 / 145 / 1/step ] DFU

11

Notch No.5:
Brightness

[ 0 to 255 / 128 / 1/step ] DFU

12

Notch No.5: Contrast

[ 0 to 255 / 128 / 1/step ] DFU

13

Notch No.5: Threshold

[ 0 to 255 / 135 / 1/step ] DFU

003

14

Notch No.4(Middle):
Brightness

*

NV

[ 0 to 255 / 128 / 1/step ] DFU

«
...
612
613
614
615
616
...
»

Содержание G060



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды