Gestetner G060 Скачать руководство пользователя страница 514

Страница: 514 / 1106

SC TABLE

G570

4-32

SC No.

Item

Definition

Possible Cause

Related

SCs

Troubleshooting Procedure

Type

SC 685

(CF)

SBU-IPU
communication
error

•

During data transfer, a

checksum error occurs.

•

During any operation

except initialization, the
SBU sends a hardware-
reset acknowledgement
to the IPU.

•

Scanner unit cable

connector loose

•

SBU board defective

•

IPU board defective

•

External noise

1. Turn the main switch off and on.
2. Shut out the external noise.
3. Check the cable connection of the

scanner unit.

4. Replace the SBU board.
5. Replace the IPU board.

SC 686

(CF)

BCU-IPU
communication
error

•

After the machine is

powered on or recovering
from the power save
mode, timeout occurs
during BCU
communication.

•

The break signal is

received after the
communication is
normally established with
the BCU.

•

Timeout occurs while the

communication with the
BCU is retried after a
communication error.

•

Board connector

between BCU and
controller loose

•

Board connector

between controller
and bridge board
loose

•

Board connector

between bridge board
and IPU loose

•

BCU board defective

•

IPU board defective

•

Controller board

defective

•

Bridge board

defective

1. Turn the main switch off and on.
2. Check the cable connection between

the board connector and BCU.

3. Check the cable connection between

controller and bridge board.

4. Check the cable connection between

bridge board and IPU.

5. Replace the BCU board.
6. Replace the IPU board.
7. Replace the controller board.
8. Replace the bridge board.

SC 687

Memory address
command error

The BCU does not receive a
memory address command
from the controller 60
seconds after paper is in the
position for registration.

•

Loose connection

•

Defective controller

•

Defective BCU

1. Turn the main switch off and on.
2. Check if the controller is firmly

connected to the BCU.

3. Replace the controller.
4. Replace the BCU.

Содержание G060



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание G060

Отзывы:

Бренды по названию

Популярные бренды

Gestetner G060, Руководство по обслуживанию

Результаты поиска

Содержание G060

Отзывы:

Бренды по названию

Популярные бренды