Gestetner G060 Скачать руководство пользователя страница 450

Страница: 450 / 1106

IMAGE ADJUSTMENT

G570

3-2

3.3 IMAGE

ADJUSTMENT

3.3.1 PRINTING

Leading edge registration

See the service manual for the printer mainframe.

Side-to-side registration

See the service manual for the printer mainframe.

3.3.2 SCANNING

Before doing the following scanner adjustments, perform or check the printing
registration/side-to-side adjustment and the blank margin adjustment.

NOTE: Use a C4 test chart to perform the following adjustments.

Scanner sub-scan magnification

1. Place the test chart on the exposure glass and make a

copy from one of the feed stations.

2. Check the magnification ratio. Use SP4-008 to adjust if

necessary.
Standard:

1.0%.

Scanner leading edge and side-to-side registration

1. Place the test chart on the exposure glass and make a

copy from one of the feed stations.

2. Check the leading edge and side-to-side registration,

and adjust them with the following SP modes if
necessary. Standard: 0

2mm.

SP mode

Sub-scan

SP4-010

Main-scan

SP4-011

G570R910.WMF

G570R908.WMF

A: Sub-scan magnification

A: Leading Edge Registration
B: Side-to-side Registration

Содержание G060



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание G060

Отзывы:

Бренды по названию

Популярные бренды

Gestetner G060, Руководство по обслуживанию

Результаты поиска

Содержание G060

Отзывы:

Бренды по названию

Популярные бренды