Gestetner G060 Скачать руководство пользователя страница 895 | Manualshive

Страница: 895 / 1106

Gestetner G060 Скачать руководство пользователя страница 895

Tech Service Bulletin No. G060 – 006
Page 2 of 2

SOLUTION:

PRODUCTION COUNTERMEASURE:

The temperature at which the display changes to “Ready” has been lowered by 1

°

C. This has been applied

from engine firmware version B1.17C.

NOTE:

The actual operating temperature has not been changed, only the display trigger temperature.

FIELD COUNTERMEASURE:

Update the engine firmware to version B1.17C or newer on G060-17 machines if the serial number is
between P60112xxxxx - P60201xxxxx and the engine firmware is ver B1.15E.

NOTE:

If the CF expander is installed, “Energy Saver 1 Mode” will automatically be activated (the default
changes to ON), therefore please make sure this update is performed.

NOTE:

The firmware can be downloaded through the Technology Solution Center FTP Site
http://tsc.ricohcorp.com. Refer to Facts Line Bulletin # FL002 and Publication Bulletin #023 for
more information about the FTP Internet Web Site and EPROM / Flash Card Exchange program.

ENGINE FIRMWARE VERSION CONFIRMATION PROCEDURE:

B1.17C:30

Figure 2

Engine Firmware

is B1.17C

Menu Key

Down Arrow

Figure 1

Enter Key

1.

See Figure 1 for key locations.

2.

Press the Menu Key.

3.

Press the Down Arrow and scroll to
“list / test print”.

4.

Press the Enter Key
“Config.” Page is displayed.

5.

Press enter again to print the
Configuration Page.

6.

Check the Configuration Page as
illustrated in Figure 2.

«
...
893
894
895
896
897
...
»

Содержание G060



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды