Gestetner G060 Скачать руководство пользователя страница 764 | Manualshive

Страница: 764 / 1106

Gestetner G060 Скачать руководство пользователя страница 764

BIT SWITCHES

G307

3-40

SM

3.2.5 G3 SWITCHES

G3 Switch 00

SP No. 1-105-001

No

FUNCTION

COMMENTS

0
1

Monitor speaker during
communication (tx and rx)
Bit 1

Bit 0 Setting

0

0

Disabled

0

1

Up to Phase B

1

0

All the time

1

1

Not used

(0, 0): The monitor speaker is disabled all through
the communication.
(0, 1): The monitor speaker is on up to phase B in
the T.30 protocol.
(1, 0): Used for testing. The monitor speaker is on
all through the communication. Make sure that you
reset these bits after testing.

2

Monitor speaker during
memory transmission
0: Disabled 1: Enabled

1: The monitor speaker is enabled during memory

transmission.

3-7

Not used

Do not change the settings.

G3 Switch 01

SP No. 1-105-002

No

FUNCTION

COMMENTS

0-3

Not used

Do not change the settings.

4

DIS frame length
0: 10 bytes 1: 4 bytes

1: The bytes in the DIS frame after the 4th byte will

not be transmitted (set to 1 if there are
communication problems with PC-based faxes
which cannot receive the extended DIS frames).

5

Not used

Do not change the setting.

6

CED/ANSam transmission
0: Disabled
1: Enabled

Do not change this setting, unless the
communication problem is caused by the
CED/ANSam transmission.

7

Not used

Do not change the setting.

G3 Switch 02

SP No. 1-105-003

No

FUNCTION

COMMENTS

0

G3 protocol mode used
0: Standard and non-standard
1: Standard only

Change this bit to 1 only when the other end can

only communicate with machines that send T.30-
standard frames only.
1: Disables NSF/NSS signals (these are used in
non-standard mode communication)

1-4

Not used

Do not change the settings.

5

Use of modem rate history for
transmission using
Quick/Speed Dials
0: Disabled
1: Enabled

0: Communications using Quick/Speed Dials always

start from the highest modem rate.

1: The machine refers to the modem rate history for

communications with the same machine when
determining the most suitable rate for the current
communication.

6

AI short protocol (transmission
and reception)
0: Disabled 1: Enabled

Refer to Appendix B in the Group 3 Facsimile
Manual for details about AI Short Protocol.

7

Short preamble
0: Disabled 1: Enabled

Refer to Appendix B in the Group 3 Facsimile
Manual for details about Short Preamble.

«
...
762
763
764
765
766
...
»

Содержание G060



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды