manualshive.com logo in svg

Gestetner G060, Руководство по обслуживанию

Поделиться
Скачать
Gestetner G060 Скачать руководство пользователя страница 1028

 

SC TABLE 

SM 4-31 

G060 

SC No. 

Item 

Definition 

Possible Cause 

Related 

SCs 

Troubleshooting Procedure 

Type 

SC 828 

Self-diagnostic error : ROM

       

[XXXX]: Detailed error code

 

[0101] Check 

sum 

error 1 

The boot monitor and OS 
program stored in the ROM 
DIMM is checked. If the check 
sum of the program is 
incorrect, this SC code is 
displayed.  

[0104] Check 

sum 

error 2 

All areas of the ROM DIMM 
are checked. If the check sum 
of all programs stored in the 
ROM DIMM is incorrect, this 
SC code is displayed. 

[0105] 

ROM error 

The ROM DIMM is not of the 
recognized type. 

• 

Defective ROM DIMM 

• 

Defective controller 

 

1. Turn the main switch on and off. 
2. Replace the ROM DIMM 
3. Replace the controller. 

CTL 

SC829 

Self-diagnosis error: optional RAM       [XXXX]: Detailed error code 

[0302] Composition 

error (Slot 0) 

The result of checking the 
composition data of the RAM 
in Slot 0 (CN5) on the 
controller is incorrect. 

[0401] Verification 

error (Slot 1) 

The data stored in the RAM in 
Slot 1 does not match the data 
when reading. 

[0402] Composition 

error (Slot 1) 

The result of checking the 
composition data of the RAM 
in Slot 1 (CN6) on the 
controller is incorrect. 

• 

Not specified RAM 
DIMM installed 

• 

Defective RAM DIMM 

 

1. Turn the main switch off and on. 
2. Replace the RAM DIMM. 
3. Replace the controller board. 

CTL 

SC 833 
[0F21] 

Self-diagnostic 
error: I/F error 

The controller detects that the 
BCU is not properly 
connected. 

• 

Loose connection 

• 

Defective controller 

• 

Defective BCU 

 

1. Turn the main switch off and on. 
2. Check the connection between the 

BCU and controller. 

3. Replace the controller. 
4. Replace the BCU 
 
 
 
. 

CTL 

Rev. 09/2003 

Содержание G060



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды