Gestetner G060 Скачать руководство пользователя страница 699

Страница: 699 / 1106

ax Un

307

FAX UNIT

1-3

G307

5. Attach the serial number decal [A] to the rear cover.

6. Attach the super G3 decal [B] as shown

7. If the ADF has been installed, insert the stamp cartridge [C] into the ADF as

shown.

8. Connect the telephone line to the “LINE” jack at the rear of the machine.

9. Plug in the machine and turn on the main power switch.

NOTE: The machine must be connected to a properly-grounded socket outlet.

10. Be sure to set the clock. (Date and time)

11. Enter service mode and program the serial number into the fax unit (SP3-102-

000). The serial number can be found on the serial number label (attached to
the machine in step 5).

G307I507.WMF

G307I105.WMF

G307I106.WMFWMF

[B]

[A]

[C]

Содержание G060



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание G060

Отзывы:

Бренды по названию

Популярные бренды

Gestetner G060, Руководство по обслуживанию

Результаты поиска

Содержание G060

Отзывы:

Бренды по названию

Популярные бренды