manualshive.com logo in svg

Gestetner G060, Руководство по обслуживанию

Поделиться
Скачать
Gestetner G060 Скачать руководство пользователя страница 359

RIGHT TRAY PAPER END DETECTION

SM

10-17

G569

La

rg

e

Cap

acit

y

 T

ra

y

G

569

2.7  RIGHT TRAY PAPER END DETECTION

The paper end sensor [A] detects when copy paper in the right tray runs out.

When there is paper in the tray, the paper pushes up the paper end feeler [B] and
causes the actuator to enter the sensor. When paper runs out, the feeler drops and
the actuator leaves the sensor, and the machine detects that there is no paper in
the tray.

When the tray is being pulled out, the lever [E] lifts the pick-up roller and this also
lifts up the feeler.

G569D106.WMF

G569D111.WMF

[D]

[E]

[A]

[B]

[C]

Содержание G060



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды