Gestetner G060 Скачать руководство пользователя страница 795

Страница: 795 / 1106

ax Un

307

NCU PARAMETERS

3-71

G307

Address

Function

Unit

Remarks

6805A1

Acceptable CED detection frequency
upper limit (high byte)

6805A2

Acceptable CED detection frequency
upper limit (low byte)

BCD (Hz)

If both addresses contain
FF(H), tone detection is
disabled.

6805A3

Acceptable CED detection frequency
lower limit (high byte)

6805A4

Acceptable CED detection frequency
lower limit (low byte)

BCD (Hz)

If both addresses contain
FF(H), tone detection is
disabled.

6805A5

CED detection time

20 ms

Factory setting: 200 ms

6805A6

Acceptable CNG detection frequency
upper limit (high byte)

6805A7

Acceptable CNG detection frequency
upper limit (low byte)

BCD (Hz)

If both addresses contain
FF(H), tone detection is
disabled.

6805A8

Acceptable CNG detection frequency
lower limit (high byte)

6805A9

Acceptable CNG detection frequency
lower limit (low byte)

BCD (Hz)

If both addresses contain
FF(H), tone detection is
disabled.

6805AA

Not used

Do not change the
setting.

6805AB

CNG on time

20 ms

Factory setting: 500 ms

6805AC

CNG off time

20 ms

Factory setting: 200 ms

6805AD

Number of CNG cycles required for
detection

The data is coded in the
same way as address
680533.

6805AE

Not used

Do not change the
settings.

6805AF

Acceptable AI short protocol tone
(800Hz) detection frequency upper
limit (high byte)

6805B0

Acceptable AI short protocol tone
(800Hz) detection frequency upper
limit (low byte)

Hz (BCD)

If both addresses contain
FF(H), tone detection is
disabled.

6805B1

Acceptable AI short protocol tone
(800Hz) detection frequency lower
limit (high byte)

6805B2

Acceptable AI short protocol tone
(800Hz) detection frequency lower
limit (low byte)

Hz(BCD)

If both addresses contain
FF(H), tone detection is
disabled.

6805B3

Detection time for 800 Hz AI short
protocol tone

20 ms

Factory setting: 360 ms

6805B4

PSTN: Tx level from the modem

-N – 3 dBm

SP2-103-002 (parameter
01).

6805B5

PSTN: 1100 Hz tone transmission
level

- N 6805B4 - 0.5N 6805B5 –3.5 (dB)
See Note 7.

6805B6

PSTN: 2100 Hz tone transmission
level

- N6805B4 - 0.5N 6805B6 –3 (dB)
See Note 7.

6805B7

PABX: Tx level from the modem

- dBm

Содержание G060



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание G060

Отзывы:

Бренды по названию

Популярные бренды

Gestetner G060, Руководство по обслуживанию

Результаты поиска

Содержание G060

Отзывы:

Бренды по названию

Популярные бренды