Gestetner G060 Скачать руководство пользователя страница 932 | Manualshive

Страница: 932 / 1106

Gestetner G060 Скачать руководство пользователя страница 932

FIRMWARE HISTORY

G060 14-6 SM

3. CONTROLLER FIRMWARE MODIFICATION HISTORY

CONTROLLER FIRMWARE MODIFICATION HISTORY

DESCRIPTION OF MODIFICATION

FIRMWARE

LEVEL

SERIAL

NUMBER

FIRMWARE

VERSION

!

Installed from the first mass production run.

G0605910

G

G0605911

G

July 2001

2.00

!

“Asia” has been added to the destination
code.

G0605910

H

G0605911

H

July 2001

2.01

G0775910
G0775911

August

2001

(See Note 1)

2.04

The following problem has been corrected:

!

When designating the Finisher shift tray 1
for paper output tray as default, paper is not
fed out to shift tray 1.

The counter click up specification has been
changed as follows:

Old Specification:

!

Machine counts a page up as black or

color based on the color data sent from the
application. Therefore if a document from
the PC contains blank (but defined) spaces
highlighted in red, e.g., the controller
interprets this as color data and counts it as
a color print.

New Specification:

!

The machine counts up the page as B/W or
color based on the CMYK data, i.e. the
actual toner colors used to develop the
image, regardless of the actual color data
from the application.

!

To meet the CPU specification change from
250MHz to 300MHz.

Color profile of the PCL driver has been
changed to Ver. 1.1.2a.

The following problem has been corrected.

!

B&W prints cannot be made if color toner is
empty.

!

HDD format cannot be done when SC860 is
detected.

!

CRD version of PS3 has been updated to
Ver. 1.2.1.

!

Presentation color profile version of PCL
has been updated to Ver. 1.2.1.
(Photographic color profile stays the same
as Ver. 1.1.2a.)

G0775910

A

G0775911

A

NA 2.05

NOTE 1-

The Meter Click counter

specification has been changed from the
controller firmware (Ver. 2.04). The
machines with Ver. 2.01 or older have been
reworked in local. However, some
machines have been released to the
market without modification. So, please
make sure that the version of the engine
main firmware is “2.04” or later at
installation or next visit. If not, please
update it to the latest firmware.

Rev. 10/2002

«
...
930
931
932
933
934
...
»

Содержание G060



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды